Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261285 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84140 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LH Side Type)

a.
E139363C07
1.219,1.521 1.073,1.948 true 1.792,1.531 1.958,1.906 true 1.063,1.531 0.615,1.531 true 1.365,1.531 1.469,1.917 true 1.917,1.927 2.229,2.135 0.313,0.208 10 false EL 1.458,1.927 1.604,2.104 0.146,0.177 10 false T 0.469,1.448 0.625,1.604 0.156,0.156 10 false A 1.01,1.958 1.219,2.115 0.208,0.156 10 false H 0.073,0.104 0.385,0.344 0.313,0.24 10 false *a
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

18 (T) - 15 (EL) Light control switch OFF or DRL-OFF 10 kΩ or higher
19 (H) - 15 (EL)
20 (A) - 15 (EL)
20 (A) - 15 (EL) Light control switch AUTO or DRL Below 1 Ω
18 (T) - 15 (EL) Light control switch Tail Below 1 Ω
18 (T) - 15 (EL) Light control switch Head Below 1 Ω
19 (H) - 15 (EL)




b.
E139363C08
1.948,1.521 2.031,1.917 true 1.813,1.521 1.729,1.906 true 1.49,1.521 1.281,1.885 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.188,1.917 1.469,2.115 0.281,0.198 10 false HF 1.979,1.938 2.26,2.115 0.281,0.177 10 false HU 1.646,1.938 1.906,2.104 0.26,0.167 10 false EL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

14 (HU) - 15 (EL) Headlight dimmer switch flash Below 1 Ω
17 (HF) - 15 (EL)
14 (HU) - 15 (EL) Headlight dimmer switch high beam Below 1 Ω




c.
E139363C09
2.375,1.521 2.833,1.521 true 2.271,1.875 2.208,1.51 true 1.979,1.938 2.073,1.521 true 1.698,1.938 1.792,1.521 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 2.885,1.427 3.188,1.646 0.302,0.219 10 false TL 2.219,1.938 2.521,2.156 0.302,0.219 10 false TR 1.885,1.958 2.188,2.177 0.302,0.219 10 false CR 1.604,1.958 1.906,2.177 0.302,0.219 10 false EL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the turn signal light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

11 (TL) - 15 (EL) Turn signal switch neutral 10 kΩ or higher
12 (TR) - 15 (EL)
13 (CR) - 15 (EL)
11 (TL) - 15 (EL) Turn signal switch left turn
(self cancel condition)
Below 1 Ω
11 (TL) - 15 (EL) Turn signal switch left turn
(cancel ratchet operation condition)
Below 1 Ω
11 (TL) - 13 (CR)
13 (CR) - 15 (EL)
12 (TR) - 15 (EL) Turn signal switch right turn
(self cancel condition)
Below 1 Ω
12 (TR) - 15 (EL) Turn signal switch right turn
(cancel ratchet operation condition)
Below 1 Ω
12 (TR) - 13 (CR)
13 (CR) - 15 (EL)


HINT:
·

The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).





d.
E139363C11
1.365,1.313 1.573,0.573 true 1.219,1.323 1.073,0.583 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.615,0.479 2.01,0.677 0.396,0.198 10 false LFG 0.76,0.469 1.156,0.667 0.396,0.198 10 false BFG
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the front fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

9 (BFG) - 8 (LFG) Front fog light switch off 10 kΩ or higher
9 (BFG) - 8 (LFG) Front fog light switch on Below 1 Ω




e.
E139363C12
1.51,1.323 1.719,0.583 true 1.354,1.323 1.208,0.583 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.76,0.479 2.156,0.677 0.396,0.198 10 false B 0.896,0.469 1.292,0.667 0.396,0.198 10 false LFG
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the rear fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

7 (B) - 8 (LFG) Rear fog light switch off 10 kΩ or higher
7 (B) - 8 (LFG) Rear fog light switch on Below 1 Ω




Hide 84140 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RH Side Type)

a.
E139363C10
2.083,1.531 1.938,1.958 true 2.229,1.521 2.396,1.896 true 2.833,1.51 2.385,1.51 true 1.646,1.542 1.552,1.906 true 1.438,1.938 1.75,2.146 0.313,0.208 10 false EL 1.875,1.99 2.021,2.167 0.146,0.177 10 false T 2.906,1.427 3.083,1.594 0.177,0.167 10 false A 2.385,1.917 2.594,2.073 0.208,0.156 10 false H 0.073,0.104 0.385,0.344 0.313,0.24 10 false *a
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

11 (A) - 16 (EL) Light control switch OFF or DRL-OFF 10 kΩ or higher
12 (H) - 16 (EL)
13 (T) - 16 (EL)
11 (A) - 16 (EL) Light control switch AUTO or DRL Below 1 Ω
13 (T) - 16 (EL) Light control switch Tail Below 1 Ω
12 (H) - 16 (EL) Light control switch Head Below 1 Ω
13 (T) - 16 (EL)




b.
E139363C13
1.938,1.531 2.167,1.917 true 1.635,1.531 1.729,1.906 true 1.49,1.521 1.281,1.885 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.198,1.906 1.479,2.104 0.281,0.198 10 false HU 2.135,1.948 2.417,2.125 0.281,0.177 10 false HF 1.677,1.938 1.938,2.104 0.26,0.167 10 false EL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

14 (HF) - 16 (EL) Headlight dimmer switch flash Below 1 Ω
17 (HU) - 16 (EL)
17 (HU) - 16 (EL) Headlight dimmer switch high beam Below 1 Ω




c.
E139363C14
0.594,1.531 1.052,1.531 true 1.406,1.896 1.344,1.531 true 1.76,1.938 1.646,1.531 true 1.135,1.906 1.208,1.542 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.052,1.948 1.354,2.167 0.302,0.219 10 false TL 0.354,1.438 0.656,1.656 0.302,0.219 10 false TR 1.333,1.948 1.635,2.167 0.302,0.219 10 false CR 1.719,1.958 2.021,2.177 0.302,0.219 10 false EL
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the turn signal light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

19 (TL) - 16 (EL) Turn signal switch neutral 10 kΩ or higher
20 (TR) - 16 (EL)
18 (CR) - 16 (EL)
19 (TL) - 16 (EL) Turn signal switch left turn
(self cancel condition)
Below 1 Ω
19 (TL) - 16 (EL) Turn signal switch left turn
(cancel ratchet operation condition)
Below 1 Ω
19 (TL) - 18 (CR)
18 (CR) - 16 (EL)
20 (TR) - 16 (EL) Turn signal switch right turn
(self cancel condition)
Below 1 Ω
20 (TR) - 16 (EL) Turn signal switch right turn
(cancel ratchet operation condition)
Below 1 Ω
20 (TR) - 18 (CR)
18 (CR) - 16 (EL)


HINT:
·

The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 6°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch is operated within 12°).





d.
E139363C15
2.229,1.323 2.438,0.583 true 2.083,1.313 1.938,0.573 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.615,0.479 2.01,0.677 0.396,0.198 10 false LFG 2.5,0.469 2.896,0.667 0.396,0.198 10 false BFG
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the front fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

2 (BFG) - 3 (LFG) Front fog light switch off 10 kΩ or higher
2 (BFG) - 3 (LFG) Front fog light switch on Below 1 Ω




e.
E139363C16
2.083,1.333 2.292,0.594 true 1.927,1.302 1.781,0.563 true 0.135,0.156 0.531,0.417 0.396,0.26 10 false *a 1.656,0.469 2.052,0.667 0.396,0.198 10 false B 2.354,0.49 2.75,0.688 0.396,0.198 10 false LFG
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the rear fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the headlight dimmer switch assembly.

4 (B) - 3 (LFG) Rear fog light switch off 10 kΩ or higher
4 (B) - 3 (LFG) Rear fog light switch on Below 1 Ω