Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261286 HAZARD WARNING SWITCH G

LIGHTING (EXT)  HAZARD WARNING SWITCH  INSPECTION  


PROCEDURE

Hide 84330 1.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for 5L-E)

E282730C05
0.115,0.125 0.354,0.344 0.24,0.219 10 false *a
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)


a.

Inspect the hazard warning signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the hazard warning signal switch assembly.

3 - 15 Hazard warning signal switch OFF 10 kΩ or higher
Hazard warning signal switch ON Below 5 Ω




b.

Inspect the Illumination.

i.
E282730C04
2.01,1.313 2.125,1.792 true 1.042,0.375 1.208,1.063 true 2.021,1.802 2.417,2.021 0.396,0.219 10 false ILL+ 0.063,0.083 0.302,0.302 0.24,0.219 10 false *a 0.771,0.281 1.167,0.5 0.396,0.219 10 false ILL-
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)


Apply battery voltage to the connector and check the illumination condition.

OK:
Battery Connection Specified Condition

If the result is not as specified, replace the hazard warning signal switch assembly.

Positive (+) → 11(ILL+)
Negative (-) → 7(ILL-)
Illuminates




Hide 84010A 2.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY (except 5L-E)

a.
E376453C01
0.854,1.813 1.271,1.396 true 0.75,0.938 1.281,0.938 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 0.563,1.771 1.021,1.969 0.458,0.198 10 false HAZ 0.438,0.865 0.896,1.063 0.458,0.198 10 false GND
*a Component without harness connected
(Integration Control and Panel Assembly)


Inspect the hazard warning signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

If the result is not as specified, replace the integration control and panel assembly.

8(HAZ) - 4(GND) Hazard warning signal switch OFF 10 kΩ or higher
Hazard warning signal switch ON Below 1 Ω




b.

Inspect the Illumination.

i.
E376453C02
1.854,0.938 2.135,0.271 true 0.75,0.938 1.281,0.938 true 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 2.177,0.167 2.635,0.365 0.458,0.198 10 false ILL+ 0.438,0.865 0.896,1.063 0.458,0.198 10 false GND
*a Component without harness connected
(Integration Control and Panel Assembly)


Apply battery voltage to the connector and check the illumination condition.

OK:
Battery Connection Specified Condition

If the result is not as specified, replace the integration control and panel assembly.

Positive (+) → 2(ILL+)
Negative (-) → 4(GND)
Illuminates