Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261288 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY (for 5L-E)

E270964C43
1.5,0.198 1.938,0.479 0.438,0.281 2.198,1.219 2.74,1.146 true 1.271,1.198 0.688,1.021 true 1.708,1.333 1.583,1.771 true 0.083,0.167 0.396,0.438 0.313,0.271 10 false *a 1.406,1.813 1.875,2.083 0.469,0.271 10 false GND 2.792,1.031 3.052,1.302 0.26,0.271 10 false B 0.542,0.906 0.802,1.177 0.26,0.271 10 false B 1.615,0.24 2.073,0.438 0.458,0.198 10 false A85
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, repair or replace the wire harness or connector.

A85-3 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition

If the result is not as specified, repair or replace the wire harness or connector.

A85-1 (B) - A85-3 (GND) Always 11 to 14 V
A85-5 (B) - A85-3 (GND) Ignition switch on (IG) 11 to 14 V



c.

Reconnect the stop light switch assembly connector.


d.
E240777C26
1.521,0.177 1.958,0.417 0.438,0.24 1.948,1.719 1.75,1.052 true 1.542,1.073 1.177,1.531 true 1.917,1.073 2.26,1.51 true 0.115,0.125 0.354,0.354 0.24,0.229 10 false *a 1.844,1.76 2.292,1.99 0.448,0.229 10 false GND 1.063,1.479 1.271,1.708 0.208,0.229 10 false L 2.313,1.427 2.521,1.656 0.208,0.229 10 false L 1.615,0.208 2.073,0.406 0.458,0.198 10 false A85
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the stop light switch assembly.

A85-2 (L) - A85-3 (GND) Ignition switch off, brake pedal not depressed Below 1 V
A85-2 (L) - A85-3 (GND) Ignition switch off, brake pedal depressed 11 to 14 V
A85-4 (L) - A85-3 (GND) Ignition switch on (IG), brake pedal not depressed 11 to 14 V
A85-4 (L) - A85-3 (GND) Ignition switch on (IG), brake pedal depressed Below 1 V



Hide 84340 2.INSPECT STOP LIGHT SWITCH ASSEMBLY (except 5L-E)

a.
E361512C02
1.49,0.25 1.896,0.51 0.406,0.26 1.333,1.177 1.177,1.771 true 2.021,1.177 2.083,1.813 true 2.26,1.135 2.792,1.135 true 0.177,0.146 0.49,0.302 0.313,0.156 10 false *a 1.563,0.281 1.875,0.438 0.313,0.156 10 false A99 1.021,1.813 1.438,2.01 0.417,0.198 10 false GND 2.063,1.865 2.375,2.021 0.313,0.156 10 false B 2.854,1.042 3.167,1.198 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

If the result is not as specified, repair or replace the wire harness or connector.

A99-2 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition

If the result is not as specified, repair or replace the wire harness or connector.

A99-7 (B) - A99-2 (GND) Always 11 to 14 V
A99-6 (B) - A99-2 (GND) Ignition switch on (IG) 11 to 14 V



c.

Reconnect the stop light switch assembly connector.


d.
E233300C83
1.469,0.271 1.854,0.531 0.385,0.26 1.927,1.115 2.406,1.677 true 2.073,1.063 2.531,0.76 true 1.813,1.115 1.99,1.677 true 1.26,0.594 1.542,1.063 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.302 1.99,0.563 0.448,0.26 10 false A99 2.583,0.677 3.031,0.896 0.448,0.219 10 false OUT 2,1.708 2.313,1.917 0.313,0.208 10 false L 2.302,1.698 2.802,1.917 0.5,0.219 10 false GND 1.167,0.49 1.479,0.698 0.313,0.208 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

If the result is not as specified, replace the stop light switch assembly.

A99- 1 (OUT) - A99-2 (GND) Brake pedal not depressed 0 to 1.5 V
A99-1 (OUT) - A99-2 (GND) Brake pedal depressed 7.5 to 14 V
A99-3 (L) - A99-2 (GND) Brake pedal not depressed 7.5 to 14 V
A99-3 (L) - A99-2 (GND) Brake pedal depressed 0 to 1.5 V
A99-5 (L) - A99-2 (GND) Brake pedal not depressed 7.5 to 14 V
A99-5 (L) - A99-2 (GND) Brake pedal depressed 0 to 1.5 V