Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › COMBINATION SWITCH › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0326170 COMBINATION SWITCH G

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY (w/ Module Switch (2nd Start))

a.
C380114C01
2.479,1.781 2.479,1.344 true 0.792,1.781 0.792,1.344 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.365,1.813 2.719,2.021 0.354,0.208 10 false 2ND 0.76,1.802 0.917,2 0.156,0.198 10 false E
*a Component without harness connected
(Combination Switch Assembly (w/ Module Switch (2nd Start)))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) Combination switch (2nd Start) pushed and held Below 1 Ω
Combination switch (2nd Start) not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly (w/ Module Switch (2nd Start)).


b.
C380114C02
2.646,1.781 2.646,1.344 true 1.198,0.333 1.031,0.333 1.031,0.333 0.781,1.031 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.24,0.271 1.583,0.469 0.344,0.198 10 false ILL-
*a Component without harness connected
(Combination Switch Assembly (w/ Module Switch (2nd Start)))


Apply battery voltage between the terminals of the combination switch assembly (w/ Module Switch (2nd Start)), and check the illumination condition of the combination switch assembly (w/ Module Switch (2nd Start)).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly (w/ Module Switch (2nd Start)).


Hide 84970E 2.INSPECT NO. 2 COMBINATION SWITCH ASSEMBLY (w/o Module Switch (2nd Start))

a.
C380114C01
2.479,1.781 2.479,1.344 true 0.792,1.781 0.792,1.344 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.365,1.813 2.719,2.021 0.354,0.208 10 false 2ND 0.76,1.802 0.917,2 0.156,0.198 10 false E
*a Component without harness connected
(No. 2 Combination Switch Assembly (w/o Module Switch (2nd Start)))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) No. 2 combination switch (2nd Start) pushed and held Below 1 Ω
No. 2 combination switch (2nd Start) not pushed 10 kΩ or higher


If the result is not as specified, replace the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).


b.
C380114C02
2.646,1.781 2.646,1.344 true 1.198,0.333 1.031,0.333 1.031,0.333 0.781,1.031 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.24,0.271 1.583,0.469 0.344,0.198 10 false ILL-
*a Component without harness connected
(No. 2 Combination Switch Assembly (w/o Module Switch (2nd Start)))


Apply battery voltage between the terminals of the No. 2 combination switch assembly (w/o Module Switch (2nd Start)), and check the illumination condition of the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).