Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch) › from 2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260845 CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch) G

VF4BM TRANSFER / 4WD / AWD  CENTER DIFFERENTIAL LOCK SWITCH(w/o Combination Switch)  INSPECTION  


PROCEDURE

Hide 84970E 1.INSPECT NO. 2 COMBINATION SWITCH ASSEMBLY

a.
C380114C06
2.469,0.365 2.302,0.365 2.302,0.365 2.302,1.031 true 0.625,1.833 0.792,1.833 0.792,1.833 0.792,1.333 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 0.49,1.75 0.833,1.948 0.344,0.198 10 false E 2.51,0.281 2.927,0.49 0.417,0.208 10 false CPU
*a Component without harness connected
(No. 2 Combination Switch Assembly (Center Differential Lock Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (CPU) - 24 (E) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the No. 2 combination switch assembly (center differential lock switch).


b.
C380114C04
2.646,1.781 2.646,1.344 true 0.948,0.26 0.781,0.26 0.781,0.26 0.781,1.01 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.021,0.167 1.365,0.365 0.344,0.198 10 false ILL-
*a Component without harness connected
(No. 2 Combination Switch Assembly (Center Differential Lock Switch))


Apply battery voltage between the terminals of the No. 2 combination switch assembly (center differential lock switch), and check the illumination condition of the No. 2 combination switch assembly (center differential lock switch).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the No. 2 combination switch assembly (center differential lock switch).


Hide 84725 2.INSPECT CENTER DIFFERENTIAL LOCK SWITCH

a.
C381450C01
1.25,1.833 1.333,1.333 true 2.083,1.833 2.031,1.323 true 1.104,1.854 1.573,2.125 0.469,0.271 10 false CPU 2.094,1.854 2.438,2.073 0.344,0.219 10 false L 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a
*a Component without harness connected
(Center Differential Lock Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (L) - 5 (CPU) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the center differential lock switch.


b.
C381450C05
0.948,1.906 1.115,1.906 1.115,1.906 1.115,1.323 true 2.417,1.906 2.25,1.906 2.25,1.906 2.25,1.323 true 0.625,1.823 0.979,2.073 0.354,0.25 10 false ILL+ 2.479,1.823 2.844,2.083 0.365,0.26 10 false ILL- 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a
*a Component without harness connected
(Center Differential Lock Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the center differential lock switch.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the center differential lock switch.