Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0261252 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/o Automatic Retractable Mirror)

a.
B231580C03
1.604,3.667 1.375,4.208 true 1.448,3.677 1.167,4.208 true 1.281,3.677 0.854,4.24 true 1.948,3.667 1.938,4.208 true 2.125,3.677 2.385,4.219 true 1.771,3.667 1.646,4.219 true 2.271,3.667 2.792,4.24 true 2.438,3.656 2.938,4.021 true 2.635,3.604 3.083,3.656 true 1.135,3.667 0.656,4.094 true 0.906,3.604 0.521,3.719 true 2.583,0.25 2.146,0.26 2.146,0.26 2.146,0.802 true 1.385,2.594 1.719,2.594 1.719,2.594 1.729,2.042 true 1.073,0.344 1.406,0.344 1.406,0.344 1.417,0.781 true 0.865,0.26 1.052,0.438 0.188,0.177 10 false *b 1.583,4.24 1.74,4.396 0.156,0.156 10 false B 3.104,3.583 3.323,3.74 0.219,0.156 10 false M+ 2.969,3.938 3.323,4.094 0.354,0.156 10 false MRH 2.635,4.24 2.99,4.396 0.354,0.156 10 false MRV 2.229,4.24 2.583,4.396 0.354,0.156 10 false MLV 1.781,4.24 2.135,4.396 0.354,0.156 10 false MLH 1.313,4.25 1.448,4.396 0.135,0.146 10 false E 0.323,4.042 0.625,4.26 0.302,0.219 10 false ILL+ 0.208,3.625 0.51,3.844 0.302,0.219 10 false ILL- 2.615,0.198 2.833,0.385 0.219,0.188 10 false *a 0.958,4.25 1.229,4.438 0.271,0.188 10 false MR 0.635,4.25 0.865,4.448 0.229,0.198 10 false MF 1.198,2.5 1.51,2.698 0.313,0.198 10 false *c 0.198,2.865 0.51,3.063 0.313,0.198 10 false *d
*a Mirror Retract Switch
*b Mirror Select Switch
*c Mirror Surface Adjust Switch
*d Component without harness connected (Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (B) - 14 (MF)
12 (E) - 13 (MR)
Extended position Below 1 Ω
11 (B) - 13 (MR)
12 (E) - 14 (MF)
Retracted position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch.

i.

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Left Side):
Tester Connection Condition Specified Condition
9 (MLV) - 11 (B)
6 (M+) - 12 (E)
Up Below 1 Ω
Off 10 kΩ or higher
6 (M+) - 11 (B)
9 (MLV) - 12 (E)
Down Below 1 Ω
Off 10 kΩ or higher
10 (MLH) - 11 (B)
6 (M+) - 12 (E)
Left Below 1 Ω
Off 10 kΩ or higher
6 (M+) - 11 (B)
10 (MLH) - 12 (E)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for Right Side):
Tester Connection Condition Specified Condition
8 (MRV) - 11 (B)
6 (M+) - 12 (E)
Up Below 1 Ω
Off 10 kΩ or higher
6 (M+) - 11 (B)
8 (MRV) - 12 (E)
Down Below 1 Ω
Off 10 kΩ or higher
7 (MRH) - 11 (B)
6 (M+) - 12 (E)
Left Below 1 Ω
Off 10 kΩ or higher
6 (M+) - 11 (B)
7 (MRH) - 12 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Battery Connection Specified Condition
Battery positive (+) - 15 (ILL+)
Battery negative (-) - 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.


Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for LHD, w/ Automatic Retractable Mirror)

a.
B487116C03
2.667,0.917 2.167,0.917 true 2,1.333 2.667,1.333 true 2.667,1.75 2.083,1.76 true 0.354,4.188 1.063,3.688 true 0.75,4.156 1.25,3.719 true 1.146,4.177 1.406,3.729 true 1.448,4.167 1.583,3.729 true 1.875,4.167 1.74,3.677 true 2.146,4.146 1.896,3.719 true 2.448,4.156 2.208,3.708 true 2.75,4.146 2.583,3.719 true 2.719,0.844 3.031,1.042 0.313,0.198 10 false *a 2.688,1.25 3,1.448 0.313,0.198 10 false *b 2.688,1.667 3,1.865 0.313,0.198 10 false *c 0.135,2.792 0.448,2.99 0.313,0.198 10 false *d 0.135,4.208 0.75,4.406 0.615,0.198 10 false ILL- 0.531,4.208 1.021,4.406 0.49,0.198 10 false MSW 1.073,4.198 1.385,4.396 0.313,0.198 10 false B 1.313,4.208 1.813,4.396 0.5,0.188 10 false MSWR 1.813,4.208 2.271,4.406 0.458,0.198 10 false MAT 2.156,4.177 2.469,4.365 0.313,0.188 10 false E 2.406,4.208 2.719,4.406 0.313,0.198 10 false MR 2.729,4.208 3.344,4.406 0.615,0.198 10 false ILL+
*a Mirror Retract Switch
*b Mirror Surface Adjust Switch
*c Mirror Select Switch
*d Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (MAT) - 10 (E)
8 (MR) - 10 (E)
Driving position 10 kΩ or higher
11 (MAT) - 10 (E) AUTO position Below 1 Ω
8 (MR) - 10 (E) Retracted position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (MSWR) - 14 (MSW) R Below 10 Ω
L 90 to 110 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror surface adjust switch.

i.

Select the mirror select switch to the L position or R position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (MSWR) - 13 (B) Mirror adjust switch pressed up 90 to 110 Ω
Off 10 kΩ or higher
Mirror adjust switch pressed down 437 to 503Ω
Off 10 kΩ or higher
Mirror adjust switch pressed left 744 to 856Ω
Off 10 kΩ or higher
Mirror adjust switch pressed right 225 to 275Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check the switch illumination.

i.

Apply battery voltage between the terminals of the light and check the operation of the light.

OK:
Battery Connection Specified Condition
Battery positive (+) - 6 (ILL+)
Battery negative (-) - 15 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/o Automatic Retractable Mirror)

a.
B487117C01
0.25,1.583 0.25,1.25 0.25,1.25 1,1.25 true 2.417,2.333 2.417,1.667 true 0.469,4 0.927,3.719 true 0.531,4.083 1.083,3.729 true 0.76,4.125 1.271,3.708 true 1.073,4.104 1.417,3.719 true 1.406,4.125 1.563,3.719 true 1.771,4.177 1.729,3.688 true 2.219,4.125 2.073,3.708 true 2.021,4.135 1.896,3.708 true 2.531,4.135 2.229,3.698 true 2.531,3.521 2.552,3.125 true 2.333,3.51 2.229,3.146 true 2.354,2.333 2.667,2.531 0.313,0.198 10 false *a 0.188,1.583 0.5,1.781 0.313,0.198 10 false *b 0.177,3.927 0.49,4.125 0.313,0.198 10 false MR 0.396,4.083 0.698,4.25 0.302,0.167 10 false B 0.583,4.115 0.938,4.313 0.354,0.198 10 false ILL+ 0.917,4.125 1.24,4.313 0.323,0.188 10 false MLH 1.271,4.146 1.729,4.344 0.458,0.198 10 false MLV 1.594,4.167 2.052,4.365 0.458,0.198 10 false MRH 1.948,4.219 2.406,4.417 0.458,0.198 10 false MRV 2.281,4.219 2.74,4.417 0.458,0.198 10 false M+ 2.573,4.219 3.344,4.417 0.771,0.198 10 false ILL- 2.063,2.948 2.51,3.156 0.448,0.208 10 false MF 2.5,2.948 2.813,3.146 0.313,0.198 10 false E 0.146,2.896 0.458,3.094 0.313,0.198 10 false *c
*a Mirror Retract Switch
*b Mirror Select Switch and Mirror Surface Adjust Switch
*c Component without harness connected (Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (MF) - 15 (B)
16 (MR) - 1 (E)
Extended position Below 1 Ω
16 (MR) - 15 (B)
2 (MF) - 1 (E)
Retracted position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
12 (MLV) - 15 (B)
9 (M+) - 1 (E)
Up Below 1 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
12 (MLV) - 1 (E)
Down Below 1 Ω
Off 10 kΩ or higher
13 (MLH) - 15 (B)
9 (M+) - 1 (E)
Left Below 1 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
13 (MLH) - 1 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
10 (MRV) - 15 (B)
9 (M+) - 1 (E)
Up Below 1 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
10 (MRV) - 1 (E)
Down Below 1 Ω
Off 10 kΩ or higher
11 (MRH) - 15 (B)
9 (M+) - 1 (E)
Left Below 1 Ω
Off 10 kΩ or higher
9 (M+) - 15 (B)
11 (MRH) - 1 (E)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the switch illumination.

i.

Apply battery voltage between the terminals of the light and check the operation of the light.

OK:
Battery Connection Specified Condition
Battery positive (+) - 14 (ILL+)
Battery negative (-) - 8 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 4.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for RHD, w/ Automatic Retractable Mirror)

a.
B487118C02
0.25,1.667 0.25,1.25 0.25,1.25 1.083,1.24 true 2.417,1.667 2.417,2.167 true 0.531,4.208 1.229,3.708 true 0.781,4.24 1.396,3.719 true 1,4.24 1.552,3.719 true 1.344,4.219 1.729,3.708 true 1.76,4.229 1.865,3.708 true 2.24,4.229 2.073,3.729 true 2.677,4.219 2.198,3.708 true 2.865,4.073 2.333,3.688 true 0.198,1.656 0.51,1.854 0.313,0.198 10 false *b 2.354,2.219 2.667,2.417 0.313,0.198 10 false *a 0.333,4.219 0.792,4.417 0.458,0.198 10 false MR 0.625,4.24 0.906,4.458 0.281,0.219 10 false ILL- 0.917,4.26 1.135,4.448 0.219,0.188 10 false B 1.156,4.24 1.5,4.438 0.344,0.198 10 false ILL+ 1.542,4.25 2.156,4.448 0.615,0.198 10 false MSW 2.031,4.26 2.51,4.469 0.479,0.208 10 false MSWR 2.635,4.25 3,4.448 0.365,0.198 10 false MAT 2.917,4.104 3.427,4.302 0.51,0.198 10 false E 0.323,2.927 0.635,3.125 0.313,0.198 10 false *c
*a Mirror Retract Switch
*b Mirror Select Switch and Mirror Surface Adjust Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (MAT) - 10 (E)
17 (MR) - 10 (E)
Extended position 10 kΩ or higher
11 (MAT) - 10 (E) AUTO position Below 1 Ω
17 (MR) - 10 (E) Retracted position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (MSWR) - 13 (MSW) R Below 10 Ω
L 90 to 110 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


ii.

Select the mirror select switch to the L position or R position.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (MSWR) - 15 (B) Mirror adjust switch pressed up 90 to 110 Ω
Off 10 kΩ or higher
Mirror adjust switch pressed down 437 to 503Ω
Off 10 kΩ or higher
Mirror adjust switch pressed left 744 to 856Ω
Off 10 kΩ or higher
Mirror adjust switch pressed right 225 to 275Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the switch illumination.

i.

Apply battery voltage between the terminals of the light and check the operation of the light.

OK:
Battery Connection Specified Condition
Battery positive (+) - 14 (ILL+)
Battery negative (-) - 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.