Home › Vehicle Interior › DOOR LOCK › TRANSMITTER BATTERY(w/o Entry and Start System) › from 2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261044 TRANSMITTER BATTERY(w/o Entry and Start System) A

DOOR LOCK  TRANSMITTER BATTERY(w/o Entry and Start System)  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

Take extra care when handling these precision electronic components.


PROCEDURE

Hide 89751A 1.REMOVE TRANSMITTER HOUSING COVER (except Separate Type)

a.
B267250C04
1.708,0.833 2.094,0.833 false 2.125,0.74 2.281,0.896 0.156,0.156 10 false *1
*1 Housing Cover
V100155

Protective Tape


Using a screwdriver with its tip wrapped in protective tape, pry apart the transmitter housing cover.

NOTICE:
·

Do not use excessive force when prying apart the housing cover.

·

Remove the transmitter housing cover while the switches face downward to prevent the switch knob from falling.




Hide 89071B 2.REMOVE DOOR CONTROL TRANSMITTER MODULE SET (except Separate Type)

a.
B318044

Remove the door control transmitter module set.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.



Hide 89745A 3.REMOVE TRANSMITTER BATTERY (except Separate Type)

a.
B318045

Twist a coin in the direction of the arrow in the illustration and detach the 7 claws to remove the transmitter battery cover.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



b.
B318046

Remove the transmitter battery (lithium battery: CR2016).

NOTICE:
·

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

·

Do not push the terminals with your finger.

·

Do not forcibly pry up the transmitter battery as the terminals may be damaged.

·

Do not touch the transmitter battery with wet hands. Water may cause it to rust.

·

Do not touch or move any components inside the transmitter as this may interfere with its proper operation.




Hide 89745A 4.INSTALL TRANSMITTER BATTERY (except Separate Type)

a.
B318050

Install a new transmitter battery (lithium battery: CR2016) with the positive (+) side up, as shown in the illustration.

NOTICE:
·

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

·

Make sure that the positive (+) side and the negative (-) side of the transmitter battery are correctly matched with the transmitter terminals.

·

Do not bend the transmitter battery electrode during installation.

·

Keep the inside of the transmitter battery case free of dust and oil.




b.
B318051

Attach the 7 claws to install the transmitter battery cover.


Hide 89071B 5.INSTALL DOOR CONTROL TRANSMITTER MODULE SET (except Separate Type)

a.
B318052

Install the door control transmitter module set to the transmitter housing case from directly above.

NOTICE:
·

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

·

The switches may not be able to operate normally when the door control transmitter module set is installed with keeping its rubber projections bent.




Hide 89751A 6.INSTALL TRANSMITTER HOUSING COVER (except Separate Type)

a.
B268614

Install the transmitter housing cover onto the transmitter housing case securely.


Hide 89745E 7.REMOVE TRANSMITTER BATTERY (for Separate Type)

a.
B239791

Twist a coin in the direction of the arrow in the illustration and remove the transmitter housing cover.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



b.
B239792

Remove the transmitter battery (lithium battery: CR2032).

NOTICE:
·

Do not push the terminals with your finger.

·

Do not forcibly pry up the transmitter battery as the terminals may be damaged.

·

Do not touch the transmitter battery with wet hands. Water may cause it to rust.

·

Do not touch or move any components inside the transmitter as this may interfere with proper operation.




Hide 89745E 8.INSTALL TRANSMITTER BATTERY (for Separate Type)

a.
B239792

Install a new transmitter battery (lithium battery: CR2032) with the positive (+) side up, as shown in the illustration.

NOTICE:
·

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

·

Make sure that the positive (+) side and the negative (-) side of the transmitter battery are correctly matched with the transmitter terminals.

·

Do not bend the transmitter battery electrode during installation.

·

Keep the inside of the transmitter housing case free of dust and oil.




b.

Install the transmitter housing cover.


c.

Press one of the transmitter switches and check that the LED illuminates.