Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL TRANSMITTER(w/o Entry and Start System) › from 2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261046 DOOR CONTROL TRANSMITTER(w/o Entry and Start System) G

DOOR LOCK  DOOR CONTROL TRANSMITTER(w/o Entry and Start System)  INSPECTION  


PROCEDURE

Hide 89071B 1.INSPECT DOOR CONTROL TRANSMITTER MODULE SET (except Separate Type)

a.

Inspect the operation of the door control transmitter module set.

i.

Remove the transmitter battery (lithium battery: CR2016) from the door control transmitter module set.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL


ii.

Install a new or known good transmitter battery (lithium battery: CR2016).

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.


HINT:
B318047

If a new or known good transmitter battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the electrical key transmitter sub-assembly, as shown in the illustration.



iii.

From outside the vehicle, approximately 1 m (3.28 ft) from the driver side outside door handle, test the door control transmitter module set by pointing its key plate at the vehicle and pressing a door control transmitter module set switch.

OK:

The door lock can be operated via the door control transmitter module set.


·

The operational area differs depending on the user, the way the door control transmitter module set is held, and the location.

·

The weak electric waves from the door control transmitter module set may be affected if the area has strong electric waves or noise. The door control transmitter module set operational area may be shortened or the door control transmitter module set may not function.




b.

Inspect the transmitter battery (lithium battery: CR2016) capacity.

i.

Remove the transmitter battery (lithium battery: CR2016) from the door control transmitter module set that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



ii.
B318048

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery (lithium battery: CR2016).

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



iii.
B318049C01
0.521,0.813 1.083,0.813 false 0.292,0.75 0.604,0.948 0.313,0.198 10 false *a
*a GND


Check the transmitter battery (lithium battery: CR2016) voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set.


Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Ignition switch off, all doors closed and lock or unlock switch is pressed 2.5 to 3.2 V


If the result is not as specified, replace the transmitter battery (lithium battery: CR2016).



Hide 89742A 2.INSPECT DOOR CONTROL TRANSMITTER (for Separate Type)

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.


a.

Inspect the operation of the door control transmitter.

i.

Remove the transmitter battery (lithium battery: CR2032) from the door control transmitter.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL


ii.
B239793

Install a new or known good transmitter battery (lithium battery: CR2032).

HINT:

If a new or known good transmitter battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the electrical key transmitter sub-assembly, as shown in the illustration.



iii.

From outside the vehicle, approximately 1 m (3.28 ft) from the driver side outside door handle, test the door control transmitter by pointing its key plate at the vehicle and pressing a door control transmitter switch.

OK:

The door lock can be operated via the door control transmitter.

The LED comes on more than once.


·

The operational area differs depending on the user, the way the door control transmitter is held, and the location.

·

The weak electric waves from the door control transmitter may be affected if the area has strong electric waves or noise. The door control transmitter operational area may be shortened or the door control transmitter may not function.




b.

Inspect the transmitter battery (lithium battery: CR2032) capacity.

i.

Remove the transmitter battery (lithium battery: CR2032) from the door control transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



ii.
B239794

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery (lithium battery: CR2032).

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter from being damaged.



iii.
B359151C01
1.923,1.001 2.293,0.769 2.293,0.769 2.529,0.769 false 2.55,0.675 2.866,0.865 0.316,0.191 10 *a
*a GND


Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter.


Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Ignition switch off, all doors closed and lock or unlock switch is pressed 2.5 to 3.2 V


If the result is not as specified, replace the transmitter battery (lithium battery: CR2032).