Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are stored.

These DTCs are also stored when calibration has not been completed.

DTC Code DTC Detection Condition Trouble Area
C1381 At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

A/BAG-IG2 fuse

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Yaw rate and acceleration sensor (Airbag sensor assembly) power source circuit



WIRING DIAGRAM

C240027E23
4.979,3.531 6.688,3.948 1.708,0.417 10 false Skid Control ECU (Master Cylinder Solenoid) 0.698,4.177 2.5,4.406 1.802,0.229 10 false : CAN Communication line 2.615,1.948 3.479,2.219 0.865,0.271 10 false A/BAG IG2 0.958,1.76 1.271,1.979 0.313,0.219 10 false IG2 1.271,1.656 1.552,1.917 0.281,0.26 10 false 21 1.271,2.594 1.573,2.802 0.302,0.208 10 false 26 1.271,2.229 1.51,2.438 0.24,0.208 10 false 25 1,2.698 1.26,2.927 0.26,0.229 10 false E2 0.99,2.344 1.229,2.583 0.24,0.24 10 false E1 0.094,3.49 2.292,3.844 2.198,0.354 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.104,3.281 0.375,3.458 0.271,0.177 10 false G1 4.979,3.354 5.438,3.552 0.458,0.198 10 false A7

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TEST MODE PROCEDURE).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC (CAN COMMUNICATION SYSTEM)


Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (w/ Central Gateway ECU) B
CAN DTC is output (w/o Central Gateway ECU) C


A

2.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the G1 yaw rate and acceleration sensor (airbag sensor assembly) connector.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch ON.


f.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


g.
U156238E05
1.135,1.5 0.573,1.5 true 0.24,1.427 0.49,1.604 0.25,0.177 10 false IG2 0.177,0.135 0.406,0.333 0.229,0.198 10 false *a 1.656,0.385 1.979,0.573 0.323,0.188 10 false G1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Disconnect the G1 yaw rate and acceleration sensor (airbag sensor assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-25 (E1) - Body ground Always Below 1 Ω
G1-26 (E2) - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.



c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1381 is not output A
DTC C1381 is output B



A

B