Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SENDER GAUGE ASSEMBLY (for Single Tank Type) › from 2017.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260583 FUEL SENDER GAUGE ASSEMBLY(for Single Tank Type) G

1GD-FTV FUEL  FUEL SENDER GAUGE ASSEMBLY(for Single Tank Type)  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY (for 5 Door)

a.

Check the fuel sender gauge assembly output voltage.

i.
A399731C02
2.292,0.833 2.917,0.833 true 1.75,0.729 2.656,0.333 2.656,0.333 2.906,0.333 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.792,1.396 2.104,1.552 0.313,0.156 10 false *b 2.99,0.75 3.302,0.948 0.313,0.198 10 false FV 2.979,0.26 3.292,0.458 0.313,0.198 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A410374C01
1.729,1.479 1.729,0.99 true 0.677,0.885 1.208,0.885 true 0.344,2.229 0.719,2.229 true 0.729,4.448 1.073,4.448 false 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.635,1.51 1.948,1.708 0.313,0.198 10 false FE 0.438,0.802 0.75,1 0.313,0.198 10 false FR 0.177,2.125 0.479,2.292 0.302,0.167 10 false F 0.573,4.354 0.875,4.521 0.302,0.167 10 false E
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.255 to 4.605 V*
Float position is E (lower) 0.345 to 0.695 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage(F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage(E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.



Hide 83320B 2.INSPECT FUEL SENDER GAUGE ASSEMBLY (for 3 Door)

a.

Check the fuel sender gauge assembly output voltage.

i.
A399733C02
1.969,0.75 2.615,0.75 true 1.75,0.76 2.375,0.354 2.375,0.354 2.615,0.354 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.781,1.417 2.094,1.573 0.313,0.156 10 false *b 2.688,0.281 3,0.479 0.313,0.198 10 false FE 2.688,0.677 3,0.875 0.313,0.198 10 false FV
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A410375C01
1.552,1.375 1.552,0.563 true 0.656,0.49 1.25,0.49 true 0.906,2.104 0.438,2.104 true 0.781,4.458 1.125,4.458 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 1.292,0.406 1.458,0.604 0.167,0.198 10 false 3 1.521,0.406 1.688,0.604 0.167,0.198 10 false 2 1.74,0.406 1.906,0.604 0.167,0.198 10 false 1 1.469,1.396 1.75,1.594 0.281,0.198 10 false FE 0.448,0.385 0.729,0.583 0.281,0.198 10 false FR 0.938,2.01 1.25,2.167 0.313,0.156 10 false F 0.625,4.375 0.938,4.531 0.313,0.156 10 false E
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.255 to 4.605 V*
Float position is E (lower) 0.345 to 0.695 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage(F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage(E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.