Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type) › from 2017.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260584 FUEL SENDER GAUGE ASSEMBLY(for Double Tank Type) G

1GD-FTV FUEL  FUEL SENDER GAUGE ASSEMBLY(for Double Tank Type)  INSPECTION  


PROCEDURE

Hide 83320 1.INSPECT FUEL SENDER GAUGE ASSEMBLY (for Fuel Main Tank)

a.

Check the fuel sender gauge assembly output voltage.

i.
A399731C02
2.292,0.833 2.917,0.833 true 1.75,0.729 2.656,0.333 2.656,0.333 2.906,0.333 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.792,1.396 2.104,1.552 0.313,0.156 10 false *b 2.99,0.75 3.302,0.948 0.313,0.198 10 false FV 2.979,0.26 3.292,0.458 0.313,0.198 10 false FE
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A410384C01
1.729,1.552 1.729,0.99 true 0.708,0.896 1.26,0.896 true 0.281,2.188 0.688,2.188 true 0.573,4.479 0.979,4.479 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *a 1.646,1.594 1.958,1.75 0.313,0.156 10 false FE 0.458,0.802 0.771,0.958 0.313,0.156 10 false FR 0.156,2.104 0.469,2.26 0.313,0.156 10 false F 0.427,4.385 0.74,4.542 0.313,0.156 10 false E
*a Component without harness connected
(Fuel Sender Gauge Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.255 to 4.605 V*
Float position is E (lower) 0.345 to 0.695 V*


*: The output voltage changes depending on the voltage applied to the terminals.


HINT:
·

Output voltage(F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage(E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.



Hide 83320B 2.INSPECT FUEL SENDER GAUGE ASSEMBLY (for Fuel Sub Tank)

a.

Check the fuel sender gauge assembly output voltage.

i.
A410352C01
0.781,1.313 1.021,1.313 1.021,1.313 1.188,1.49 false 1.458,1.958 1.458,1.823 1.458,1.823 1.344,1.719 false 2.677,1.427 3.021,1.427 false 1.604,1.646 1.938,1.854 1.938,1.854 2.177,1.854 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 3.031,1.323 3.344,1.479 0.313,0.156 10 false *b 2.198,1.75 2.885,1.938 0.688,0.188 10 false 1 (FV) *c 1.135,1.969 1.802,2.135 0.667,0.167 10 false 2 (FE) *d 0.167,1.219 0.833,1.427 0.667,0.208 10 false 3 (FR) *e
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Voltage applied between terminals
*c Lead Wire (Red)
*d Lead Wire (Black)
*e Lead Wire (Green)


Apply 5 V between terminals 1 (FV) and 2 (FE).

NOTICE:
·

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.

·

Do not apply more than 6 V to terminals 1 (FV) and 2 (FE).



HINT:

If a stable power supply is not available, use 4 1.2 V nickel-metal hydride batteries or equivalent.



ii.
A410346C01
2.146,0.708 2.01,0.344 2.01,0.344 1.771,0.344 false 2.281,0.708 2.417,0.333 2.417,0.333 2.635,0.333 false 0.365,1.938 0.698,1.938 false 1,4.177 1.333,4.177 false 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.698,0.229 3.365,0.5 0.667,0.271 10 false 2 (FE) *b 1.177,0.25 1.844,0.521 0.667,0.271 10 false 3 (FR) *c 0.24,1.854 0.552,2.01 0.313,0.156 10 false F 0.865,4.104 1.177,4.26 0.313,0.156 10 false E
*a Component without harness connected
(Fuel Sender Gauge Assembly)
*b Lead Wire (Black)
*c Lead Wire (Green)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FE) - 3 (FR) Float position is F (upper) 4.255 to 4.605 V*
Float position is E (lower) 0.345 to 0.695 V*


*: The output voltage changes depending on the voltage applied to the terminals.


NOTICE:

Be careful when connecting the leads, as the fuel sender gauge assembly may be damaged if the leads are connected to the wrong terminals.


HINT:
·

Output voltage(F) = (0.851 x Voltage applied to terminals) to (0.921 x Voltage applied to terminals)

·

Output voltage(E) = (0.069 x Voltage applied to terminals) to (0.139 x Voltage applied to terminals)



If the result is not as specified, replace the fuel sender gauge assembly.