"Manual cut off switch" refers to the airbag cutoff switch cylinder.
The airbag cutoff switch cylinder circuit consists of the center airbag sensor and airbag cutoff switch cylinder.
The instrument panel passenger airbag can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder to the "OFF" position.
If the instrument panel passenger airbag is deactivated, the airbag cutoff indicator comes on to inform the passengers.
DTC B1651 is stored when a malfunction is detected in the airbag cutoff switch cylinder circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1651 | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff switch cylinder circuit for 2 seconds. ·
An airbag cutoff switch cylinder malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Airbag cutoff switch cylinder sub-assembly ·
Center airbag sensor |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
The 19-11 (MSW+) and 19-12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), it is necessary to release this mechanism.
w/o Side Airbag
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the center airbag sensor and airbag cut off switch cylinder.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - Body ground | Ignition switch ON | Below 1 V |
| G73-1 (PMC-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - G73-1 (PMC-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - G73-1 (PMC-) | Always | 1 MΩ or higher |
| G73-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| G73-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
| *1 | Airbag Cutoff Switch Cylinder |
| *2 | Center Airbag Sensor |
| *3 | Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder) |
| *4 | Connector C |
| *5 | Rear view of wire harness connector
(to Center Airbag Sensor) |
| *6 | Connector B |
w/ Side Airbag
| *1 | Airbag Cutoff Switch Cylinder |
| *2 | Center Airbag Sensor |
| *3 | Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder) |
| *4 | Connector C |
| *5 | Rear view of wire harness connector
(to Center Airbag Sensor) |
| *6 | Connector B |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the center airbag sensor and airbag cut off switch cylinder.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - Body ground | Ignition switch ON | Below 1 V |
| G73-1 (PMC-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - G73-1 (PMC-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-2 (PMC+) - G73-1 (PMC-) | Always | 1 MΩ or higher |
| G73-2 (PMC+) - Body ground | Always | 1 MΩ or higher |
| G73-1 (PMC-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Remove the airbag cutoff switch cylinder (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (PMC+) - 1 (PMC-) | Cutoff switch in "ON" position (Front passenger side airbag active) | 360 to 440 Ω |
| 2 (PMC+) - 1 (PMC-) | Cutoff switch in "OFF" position (Front passenger side airbag not active) | 90 to 110 Ω |
OK
NG
| *A | w/o Side Airbag |
| *B | w/ Side Airbag |
| *1 | Airbag Cutoff Switch Cylinder |
| *2 | Center Airbag Sensor |
Connect the connectors to the center airbag sensor and airbag cutoff switch cylinder.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1651 is not output.
Codes other than DTC B1651 may be output at this time, but they are not related to this check.
OK
NG