Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660  P Seat Airbag Active Mode Indicator  


DESCRIPTION

The airbag cutoff indicator circuit consists of the center airbag sensor and the airbag cutoff indicator.

The airbag cutoff indicator indicates the operation condition of the instrument panel passenger airbag, front seat side airbag and front seat outer belt.

DTC B1660 is stored when a malfunction is detected in the airbag cutoff indicator circuit.

DTC Code DTC Detection Condition Trouble Area
B1660 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff indicator circuit for 2 seconds.

·

A airbag cutoff indicator malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Telltale light assembly

·

Center airbag sensor



WIRING DIAGRAM

C217346E03
5.469,3.76 5.771,3.927 0.302,0.167 10 false G1 0.396,3.76 0.802,3.948 0.406,0.188 10 false G194 1.635,0.979 1.938,1.146 0.302,0.167 10 false 1 5.354,0.938 5.656,1.104 0.302,0.167 10 false 17 1.635,2 1.938,2.167 0.302,0.167 10 false 5 5.656,1.073 6.031,1.24 0.375,0.167 10 false P-AB 5.354,1.958 5.656,2.125 0.302,0.167 10 false 25 5.354,2.969 5.656,3.135 0.302,0.167 10 false 26 5.656,2.063 6.177,2.229 0.521,0.167 10 false E1 5.656,3.104 6.031,3.271 0.375,0.167 10 false E2 1.177,1.073 1.552,1.24 0.375,0.167 10 false OFF 1.125,2.083 1.542,2.25 0.417,0.167 10 false LAPB 0.396,3.938 1.875,4.115 1.479,0.177 10 false Telltale Light Assembly 5.469,3.927 6.854,4.125 1.385,0.198 10 false Center Airbag Sensor 2.146,3.052 3.333,3.917 1.188,0.865 10 false from ECU-IG NO.2 Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PASSENGER AIRBAG CUTOFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.

C216915E01
0.231,0.559 1.156,0.729 0.924,0.170 10 Ignition Switch 0.231,1.454 1.091,1.811 0.860,0.357 10 Airbag Cutoff Indicator 1.586,0.737 1.897,0.881 0.311,0.144 10 Off 1.586,0.312 1.824,0.465 0.239,0.154 10 ON 1.586,1.706 1.890,1.867 0.304,0.161 10 Off 1.586,1.356 1.825,1.494 0.239,0.137 10 On 3.099,0.87 3.765,1.035 0.666,0.165 10 4 seconds 4.057,0.87 4.719,1.012 0.662,0.142 10 2 seconds 4.536,2.113 7.072,2.491 2.536,0.378 10 Airbag cutoff indicator condition depends on the front passenger detection results.


b.

Check the airbag cutoff indicator operation.

HINT:

Refer to the normal condition of the airbag cutoff indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


Result
Result Proceed to
Always on A
Off B



A

2.CHECK CONNECTION OF CONNECTORS

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and telltale light.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and telltale light.


b.
C385393C01
0.073,0.125 0.385,0.281 0.313,0.156 10 false *A 0.167,2.563 0.479,2.719 0.313,0.156 10 false *B 0.448,1.938 0.76,2.094 0.313,0.156 10 false *1 2.198,1.979 2.51,2.135 0.313,0.156 10 false *2 0.438,4.219 0.75,4.375 0.313,0.156 10 false *1 2.198,4.229 2.51,4.385 0.313,0.156 10 false *2
*A w/o Side Airbag
*B w/ Side Airbag
*1 Telltale Light
*2 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and telltale light side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK PASSENGER AIRBAG CUTOFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG CUTOFF INDICATOR
a.
C216914

Connect the connector to the telltale light.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the airbag cutoff indicator operation.

OK:

The airbag cutoff indicator does not come on.




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT)
5.CHECK CENTER AIRBAG SENSOR
a.
C385391C01
0.083,0.073 0.396,0.229 0.313,0.156 10 false *A 0.125,2.167 0.438,2.323 0.313,0.156 10 false *B 0.719,1.573 1.031,1.729 0.313,0.156 10 false *1 1.74,1.927 2.052,2.083 0.313,0.156 10 false *2 1.74,3.938 2.052,4.094 0.313,0.156 10 false *2 0.677,3.927 0.99,4.083 0.313,0.156 10 false *1
*A w/o Side Airbag
*B w/ Side Airbag
*1 Telltale Light
*2 Center Airbag Sensor


Connect the connectors to the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT)
a.

w/o Side Airbag

i.

Turn the ignition switch off.

C385973C01
2.656,0.646 3.052,0.833 0.396,0.188 4.948,0.573 5.344,0.76 0.396,0.188 2.969,1.302 3.281,1.094 true 5.479,1.313 5.885,0.875 true 0.573,0.573 0.729,0.771 0.156,0.198 10 false D 0.365,0.958 0.719,1.271 0.354,0.313 10 false *1 0.833,0.781 0.99,0.979 0.156,0.198 10 false C 1.49,0.771 1.646,0.969 0.156,0.198 10 false B 1.76,0.573 1.917,0.771 0.156,0.198 10 false A 1.917,1.25 2.271,1.563 0.354,0.313 10 false *2 2.698,0.646 3.052,0.958 0.354,0.313 10 false G194 3.49,0.281 3.844,0.594 0.354,0.313 10 false *a 4.094,0.625 4.448,0.938 0.354,0.313 10 false *3 2.802,1.313 3.156,1.625 0.354,0.313 10 false OFF 5.052,0.583 5.406,0.896 0.354,0.313 10 false G1 5.948,0.229 6.302,0.542 0.354,0.313 10 false *b 6.552,0.573 6.906,0.813 0.354,0.24 10 false *4 5.313,1.313 5.667,1.625 0.354,0.313 10 false P-AB
*1 Telltale Light *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Telltale Light)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Disconnect the connectors from the center airbag sensor and telltale light.


iv.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G194-1 (OFF) - Body ground Ignition switch ON Below 1 V



vi.

Turn the ignition switch off.


vii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


viii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G194-1 (OFF) - G1-17 (P-AB) Always Below 1 Ω
G194-1 (OFF) - Body ground Always 1 MΩ or higher




b.

w/ Side Airbag

i.

Turn the ignition switch off.

C385392C01
2.667,0.688 3.052,0.938 0.385,0.25 5.021,0.51 5.333,0.708 0.313,0.198 3.052,1.417 3.271,1.083 true 5.198,1.219 5.896,0.865 true 0.292,1.24 0.604,1.396 0.313,0.156 10 false *1 1.708,1.292 2.021,1.448 0.313,0.156 10 false *2 4.125,0.635 4.438,0.792 0.313,0.156 10 false *3 6.521,0.521 6.833,0.677 0.313,0.156 10 false *4 0.521,0.792 0.677,0.99 0.156,0.198 10 false D 3.521,0.135 3.833,0.292 0.313,0.156 10 false *a 5.958,0.115 6.271,0.271 0.313,0.156 10 false *b 0.844,1.021 1,1.219 0.156,0.198 10 false C 1.51,1.01 1.667,1.208 0.156,0.198 10 false B 1.802,0.771 1.958,0.969 0.156,0.198 10 false A 2.698,0.74 3.073,0.906 0.375,0.167 10 false G194 5.073,0.531 5.354,0.698 0.281,0.167 10 false G1 2.823,1.406 3.219,1.573 0.396,0.167 10 false OFF 5.01,1.26 5.563,1.469 0.552,0.208 10 false P-AB
*1 Telltale Light *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Telltale Light)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



ii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


iii.

Disconnect the connectors from the center airbag sensor and telltale light.


iv.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G194-1 (OFF) - Body ground Ignition switch ON Below 1 V



vi.

Turn the ignition switch off.


vii.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


viii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G194-1 (OFF) - G1-17 (P-AB) Always Below 1 Ω
G194-1 (OFF) - Body ground Always 1 MΩ or higher





OK

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and telltale light.

OK:

The connectors are properly connected.




OK

8.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and telltale light.


b.
C385393C02
0.135,0.073 0.448,0.229 0.313,0.156 10 false *A 0.177,2.26 0.49,2.417 0.313,0.156 10 false *B 0.438,1.51 0.75,1.667 0.313,0.156 10 false *1 2.188,1.938 2.5,2.094 0.313,0.156 10 false *2 0.396,3.99 0.708,4.146 0.313,0.156 10 false *1 2.208,4.135 2.521,4.292 0.313,0.156 10 false *2
*A w/o Side Airbag
*B w/ Side Airbag
*1 Telltale Light
*2 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and telltale light side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT)

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - TELLTALE LIGHT)
a.

w/o Side Airbag

i.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C385973C01
2.656,0.646 3.052,0.833 0.396,0.188 4.948,0.573 5.344,0.76 0.396,0.188 2.969,1.302 3.281,1.094 true 5.479,1.313 5.885,0.875 true 0.573,0.573 0.729,0.771 0.156,0.198 10 false D 0.365,0.958 0.719,1.271 0.354,0.313 10 false *1 0.833,0.781 0.99,0.979 0.156,0.198 10 false C 1.49,0.771 1.646,0.969 0.156,0.198 10 false B 1.76,0.573 1.917,0.771 0.156,0.198 10 false A 1.917,1.25 2.271,1.563 0.354,0.313 10 false *2 2.698,0.646 3.052,0.958 0.354,0.313 10 false G194 3.49,0.281 3.844,0.594 0.354,0.313 10 false *a 4.094,0.625 4.448,0.938 0.354,0.313 10 false *3 2.802,1.313 3.156,1.625 0.354,0.313 10 false OFF 5.052,0.583 5.406,0.896 0.354,0.313 10 false G1 5.948,0.229 6.302,0.542 0.354,0.313 10 false *b 6.552,0.573 6.906,0.813 0.354,0.24 10 false *4 5.313,1.313 5.667,1.625 0.354,0.313 10 false P-AB
*1 Telltale Light *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Telltale Light)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G194-1 (OFF) - Body ground Ignition switch ON Below 1 V



iii.

Turn the ignition switch off.


iv.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G194-1 (OFF) - G1-17 (P-AB) Always Below 1 Ω
G194-1 (OFF) - Body ground Always 1 MΩ or higher




b.

w/ Side Airbag

i.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C385392C01
2.667,0.688 3.052,0.938 0.385,0.25 5.021,0.51 5.333,0.708 0.313,0.198 3.052,1.417 3.271,1.083 true 5.198,1.219 5.896,0.865 true 0.292,1.24 0.604,1.396 0.313,0.156 10 false *1 1.708,1.292 2.021,1.448 0.313,0.156 10 false *2 4.125,0.635 4.438,0.792 0.313,0.156 10 false *3 6.521,0.521 6.833,0.677 0.313,0.156 10 false *4 0.521,0.792 0.677,0.99 0.156,0.198 10 false D 3.521,0.135 3.833,0.292 0.313,0.156 10 false *a 5.958,0.115 6.271,0.271 0.313,0.156 10 false *b 0.844,1.021 1,1.219 0.156,0.198 10 false C 1.51,1.01 1.667,1.208 0.156,0.198 10 false B 1.802,0.771 1.958,0.969 0.156,0.198 10 false A 2.698,0.74 3.073,0.906 0.375,0.167 10 false G194 5.073,0.531 5.354,0.698 0.281,0.167 10 false G1 2.823,1.406 3.219,1.573 0.396,0.167 10 false OFF 5.01,1.26 5.563,1.469 0.552,0.208 10 false P-AB
*1 Telltale Light *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Telltale Light)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G194-1 (OFF) - Body ground Ignition switch ON Below 1 V



iii.

Turn the ignition switch off.


iv.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G194-1 (OFF) - G1-17 (P-AB) Always Below 1 Ω
G194-1 (OFF) - Body ground Always 1 MΩ or higher





OK

10.CHECK PASSENGER AIRBAG CUTOFF INDICATOR (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK PASSENGER AIRBAG CUTOFF INDICATOR (SOURCE VOLTAGE)
a.
C386014C02
0.479,1.031 0.927,1.25 0.448,0.219 2.406,1.604 2.063,1.375 true 0.542,1.052 0.948,1.281 0.406,0.229 10 false G194 2.448,1.531 3.063,1.729 0.615,0.198 10 false LAPB 1.604,0.438 1.917,0.635 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Telltale Light)


Turn the ignition switch off.


b.

Connect the connectors to the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G194-5 (LAPB) - Body ground Ignition switch ON 11 to 14 V




OK

11.CHECK PASSENGER AIRBAG CUTOFF INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TELLTALE LIGHT - BATTERY) OR BATTERY

11.CHECK PASSENGER AIRBAG CUTOFF INDICATOR
a.
U170015E01
0.461,0.856 0.678,1.026 0.217,0.170 10 G1 1.61,0.11 1.767,0.280 0.157,0.170 10 *a 1.572,0.95 0.599,1.591 false 0.369,1.63 0.762,1.779 0.393,0.149 10 P-AB

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the telltale light.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Check the indicator according to the value(s) in the table below.

OK:
Tester Connection Switch Condition Airbag Cutoff Indicator
G1-17 (P-AB) - Body ground Ignition switch ON Indicator comes on


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor)



OK

12.CHECK CENTER AIRBAG SENSOR

NG

12.CHECK CENTER AIRBAG SENSOR
a.
C385391C01
0.083,0.073 0.396,0.229 0.313,0.156 10 false *A 0.125,2.167 0.438,2.323 0.313,0.156 10 false *B 0.719,1.573 1.031,1.729 0.313,0.156 10 false *1 1.74,1.927 2.052,2.083 0.313,0.156 10 false *2 1.74,3.938 2.052,4.094 0.313,0.156 10 false *2 0.677,3.927 0.99,4.083 0.313,0.156 10 false *1
*A w/o Side Airbag
*B w/ Side Airbag
*1 Telltale Light
*2 Center Airbag Sensor


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the center airbag sensor.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG