Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905  Short in Front Passenger Side Pretensioner Squib Circuit  B1906  Open in Front Passenger Side Pretensioner Squib Circuit  B1907  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908  Short to B+ in Front Passenger Side Pretensioner Squib Circuit  


DESCRIPTION

The front passenger side pretensioner squib circuit consists of the center airbag sensor and front seat outer belt LH or RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side pretensioner squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1905 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the front passenger side pretensioner squib circuit during the primary check.

·

A front passenger side pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front passenger side pretensioner squib)

·

Center airbag sensor


B1906 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the front passenger side pretensioner squib circuit for 2 seconds.

·

A front passenger side pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front passenger side pretensioner squib)

·

Center airbag sensor


B1907 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the front passenger side pretensioner squib circuit for 0.5 seconds.

·

A front passenger side pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front passenger side pretensioner squib)

·

Center airbag sensor


B1908 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the front passenger side pretensioner squib circuit for 0.5 seconds.

·

A front passenger side pretensioner squib malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat outer belt assembly (Front passenger side pretensioner squib)

·

Center airbag sensor



WIRING DIAGRAM

U169901E02
0.74,3.26 3.135,3.427 2.396,0.167 10 false Front Pretensioner Squib LH 2.198,1.552 2.427,1.74 0.229,0.188 10 false L+ 4.771,1.656 5.167,1.844 0.396,0.188 10 false PP+ 2.198,2.396 2.406,2.583 0.208,0.188 10 false L- 4.781,2.5 5.177,2.688 0.396,0.188 10 false PP- 2.458,1.531 2.604,1.698 0.146,0.167 10 false 1 2.479,2.385 2.635,2.542 0.156,0.156 10 false 2 4.583,1.552 4.698,1.719 0.115,0.167 10 false 4 4.583,2.396 4.708,2.563 0.125,0.167 10 false 5 4.781,4.146 5.104,4.333 0.323,0.188 10 false R32 4.781,4.323 6.229,4.531 1.448,0.208 10 false Center Airbag Sensor 0.74,3.042 1.094,3.198 0.354,0.156 10 false R2 0.083,0.052 0.813,0.26 0.729,0.208 12 false for RHD:

U169900E02
0.74,3.229 3.135,3.396 2.396,0.167 10 false Front Pretensioner Squib RH 2.198,1.552 2.427,1.74 0.229,0.188 10 false R+ 4.771,1.667 5.167,1.854 0.396,0.188 10 false PP+ 2.198,2.396 2.406,2.583 0.208,0.188 10 false R- 4.792,2.49 5.188,2.677 0.396,0.188 10 false PP- 2.458,1.542 2.604,1.708 0.146,0.167 10 false 1 2.479,2.396 2.635,2.552 0.156,0.156 10 false 2 4.583,1.552 4.698,1.719 0.115,0.167 10 false 4 4.583,2.396 4.708,2.563 0.125,0.167 10 false 5 4.76,4.135 5.083,4.323 0.323,0.188 10 false Q1 4.781,4.313 6.229,4.521 1.448,0.208 10 false Center Airbag Sensor 0.74,3.021 1.094,3.177 0.354,0.156 10 false Q2 0.135,0.083 0.833,0.281 0.698,0.198 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result
Result Proceed to
for LHD A
for RHD B



B

2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)

A

6.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
a.
U170016E02
2.042,2.271 2.427,2.49 false 0.875,0.958 0.875,0.521 0.875,0.521 0.917,0.521 false 1.604,1.24 1.781,1.417 0.177,0.177 10 false *2 1.563,1.542 1.75,1.719 0.188,0.177 10 false *a 2.531,2.458 2.708,2.635 0.177,0.177 10 false *4 2.667,1.969 2.844,2.146 0.177,0.177 10 false *3 0.469,2.26 0.667,2.427 0.198,0.167 10 false R2 1.76,0.948 1.885,1.125 0.125,0.177 10 false A 1.24,1.167 1.365,1.344 0.125,0.177 10 false C 1.01,1.167 1.135,1.344 0.125,0.177 10 false D 1.01,0.406 1.198,0.583 0.188,0.177 10 false *1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Result
Result Proceed to
OK (for 3 Door) A
OK (for 5 Door) B
NG C

Text in Illustration
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Pretensioner Squib LH)



C

3.CHECK CONNECTOR

A

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

B

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C214775E01
1.086,1.564 1.279,1.804 0.193,0.239 10 D 0.881,1.077 1.074,1.244 0.193,0.167 10 *1 1.71,1.627 1.903,1.794 0.193,0.167 10 *2 1.318,1.564 1.530,1.785 0.211,0.221 10 C 1.902,1.26 2.095,1.444 0.193,0.184 10 A

Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor



OK

4.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.
U170017E02
0.719,0.938 0.719,0.51 0.719,0.51 0.76,0.51 false 1.281,0.938 1.281,0.51 1.281,0.51 1.323,0.51 false 1.594,2.188 1.177,2.563 false 1.75,2.188 2.094,2.51 false 0.813,0.417 1,0.594 0.188,0.177 10 false *1 1.625,1.24 1.802,1.417 0.177,0.177 10 false *3 1.656,1.542 1.844,1.719 0.188,0.177 10 false *a 2.646,2.01 2.823,2.188 0.177,0.177 10 false *4 0.469,2.24 0.667,2.406 0.198,0.167 10 false R2 1.781,0.927 1.906,1.104 0.125,0.177 10 false A 1.063,1.198 1.188,1.375 0.125,0.177 10 false C 1.417,1.198 1.542,1.375 0.125,0.177 10 false B 0.844,1.198 0.969,1.375 0.125,0.177 10 false D 1.385,0.417 1.573,0.594 0.188,0.177 10 false *2 0.948,2.479 1.229,2.625 0.281,0.146 10 false L+ 2.208,2.448 2.51,2.594 0.302,0.146 10 false L-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R2-1 (L+) - Body ground Ignition switch ON Below 1 V
R2-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (L+) - R2-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (L+) - R2-2 (L-) Always 1 MΩ or higher
R2-1 (L+) - Body ground Always 1 MΩ or higher
R2-2 (L-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Pretensioner Squib LH
*2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Pretensioner Squib LH)


OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C146261C41
0.771,0.802 0.969,1 0.198,0.198 10 false *1 0.958,1.198 1.083,1.396 0.125,0.198 10 false D 1.094,1.198 1.24,1.385 0.146,0.188 10 false C 1.479,1.281 1.677,1.448 0.198,0.167 10 false *2 1.656,0.948 1.802,1.135 0.146,0.188 10 false A
*1 Front Pretensioner Squib LH
*2 Center Airbag Sensor


Connect the connectors to the front seat outer belt LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
a.
U148391E03
2.063,2.271 2.448,2.49 false 1,0.927 1,0.49 1,0.49 1.042,0.49 false 1.594,1.25 1.771,1.427 0.177,0.177 10 false *2 1.573,1.51 1.76,1.688 0.188,0.177 10 false *a 2.542,2.427 2.719,2.604 0.177,0.177 10 false *4 2.677,1.969 2.854,2.146 0.177,0.177 10 false *3 0.458,2.24 0.677,2.406 0.219,0.167 10 false Q2 1.802,0.938 1.927,1.115 0.125,0.177 10 false A 1.229,1.167 1.354,1.344 0.125,0.177 10 false C 1.01,1.167 1.135,1.344 0.125,0.177 10 false D 1.052,0.406 1.24,0.583 0.188,0.177 10 false *1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Result
Result Proceed to
OK (for 3 Door) A
OK (for 5 Door) B
NG C

Text in Illustration
*1 Front Pretensioner Squib RH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Pretensioner Squib RH)



C

7.CHECK CONNECTOR

A

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

B

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

7.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C214775E01
1.086,1.564 1.279,1.804 0.193,0.239 10 D 0.881,1.077 1.074,1.244 0.193,0.167 10 *1 1.71,1.627 1.903,1.794 0.193,0.167 10 *2 1.318,1.564 1.530,1.785 0.211,0.221 10 C 1.902,1.26 2.095,1.444 0.193,0.184 10 A

Check that the Floor wire connector (on the front seat outer belt RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Pretensioner Squib RH
*2 Center Airbag Sensor



OK

8.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
U148392E04
0.729,0.948 0.729,0.521 0.729,0.521 0.781,0.521 false 1.26,0.958 1.26,0.531 1.26,0.531 1.302,0.531 false 1.604,2.188 1.198,2.563 false 1.74,2.188 2.094,2.563 false 0.854,0.427 1.042,0.604 0.188,0.177 10 false *1 1.594,1.229 1.771,1.406 0.177,0.177 10 false *3 1.656,1.542 1.844,1.719 0.188,0.177 10 false *a 2.719,2.01 2.896,2.188 0.177,0.177 10 false *4 0.458,2.24 0.667,2.406 0.208,0.167 10 false Q2 1.802,0.927 1.927,1.104 0.125,0.177 10 false A 1.063,1.177 1.188,1.354 0.125,0.177 10 false C 1.406,1.177 1.531,1.354 0.125,0.177 10 false B 0.833,1.177 0.958,1.354 0.125,0.177 10 false D 1.375,0.417 1.563,0.594 0.188,0.177 10 false *2 1,2.479 1.281,2.625 0.281,0.146 10 false R+ 2.156,2.49 2.458,2.635 0.302,0.146 10 false R-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q2-1 (R+) - Body ground Ignition switch ON Below 1 V
Q2-2 (R-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-1 (R+) - Q2-2 (R-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q2-1 (R+) - Q2-2 (R-) Always 1 MΩ or higher
Q2-1 (R+) - Body ground Always 1 MΩ or higher
Q2-2 (R-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Front Pretensioner Squib RH
*2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Front Pretensioner Squib RH)


OK

9.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

9.CHECK CENTER AIRBAG SENSOR
a.
C146261E84
0.823,1.104 0.823,1.49 false 0.698,1.552 0.896,1.75 0.198,0.198 10 false *1 0.958,1.198 1.083,1.396 0.125,0.198 10 false D 1.104,1.198 1.25,1.385 0.146,0.188 10 false C 1.479,1.427 1.677,1.594 0.198,0.167 10 false *2

Connect the connectors to the front seat outer belt RH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907 or B1908 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Pretensioner Squib RH
*2 Center Airbag Sensor



OK

NG