Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

for 5L-E:
C175154E11
0.06,0.839 1.054,1.051 0.994,0.211 10 from IG2 Relay 0.06,2.649 1.054,2.860 0.994,0.211 10 from IG2 Relay 1.778,1.007 2.121,1.177 0.343,0.170 10 IGN 1.629,2.779 2.204,2.942 0.575,0.163 10 GAUGE 1.697,3.37 2.233,3.547 0.537,0.177 10 ECU-B 0.465,6.338 3.001,6.515 2.536,0.177 10 : CAN Communication Line 2.906,2.565 3.159,2.769 0.253,0.205 10 28 2.913,3.16 3.124,3.330 0.211,0.170 10 26 2.92,4.155 3.124,4.366 0.205,0.211 10 21 3.158,2.663 3.453,2.846 0.295,0.184 10 IG+ 3.158,3.265 3.467,3.463 0.309,0.198 10 B 3.158,4.245 3.453,4.450 0.295,0.205 10 E2 3.654,2.054 4.088,2.196 0.434,0.142 10 CANL 3.647,2.65 4.081,2.813 0.434,0.163 10 CANH 6.151,2.056 6.585,2.198 0.434,0.142 10 CANL 6.151,2.652 6.585,2.815 0.434,0.163 10 CANH 4.131,1.919 4.398,2.088 0.267,0.170 10 39 4.138,2.507 4.364,2.684 0.225,0.177 10 40 5.873,1.928 6.133,2.119 0.260,0.191 10 22 5.873,2.531 6.112,2.714 0.239,0.184 10 13 5.866,3.546 6.078,3.751 0.211,0.205 10 25 5.873,4.138 6.098,4.329 0.225,0.191 10 26 6.151,3.66 6.362,3.816 0.211,0.156 10 E1 6.151,4.263 6.390,4.433 0.239,0.170 10 E2 5.88,0.742 6.059,0.893 0.179,0.151 10 21 6.151,0.849 6.501,1.010 0.350,0.161 10 IG2 3.049,5.599 3.351,5.762 0.302,0.163 10 G6 3.049,5.774 4.821,5.958 1.771,0.184 10 Combination Meter 5.748,5.574 6.085,5.737 0.336,0.163 10 G1 5.748,5.732 7.112,5.937 1.364,0.205 10 Center Airbag Sensor 0.214,3.249 1.046,3.460 0.832,0.211 10 from Battery

except 5L-E:
C175154E27
0.063,0.844 1.052,1.052 0.99,0.208 10 false from IG2 Relay 0.063,2.646 1.052,2.854 0.99,0.208 10 false from IG2 Relay 1.781,1.01 2.125,1.177 0.344,0.167 10 false IGN 1.625,2.781 2.198,2.948 0.573,0.167 10 false METER 1.698,3.375 2.24,3.552 0.542,0.177 10 false ECU-B 0.469,6.333 3,6.51 2.531,0.177 10 false : CAN Communication Line 2.906,2.563 3.156,2.771 0.25,0.208 10 false 22 2.917,3.146 3.125,3.313 0.208,0.167 10 false 21 2.917,4.156 3.125,4.365 0.208,0.208 10 false 20 3.156,2.667 3.448,2.854 0.292,0.188 10 false IG+ 3.156,3.26 3.469,3.458 0.313,0.198 10 false B 3.156,4.25 3.448,4.458 0.292,0.208 10 false E2 3.656,2.052 4.094,2.198 0.438,0.146 10 false CANL 3.646,2.646 4.083,2.813 0.438,0.167 10 false CANH 6.146,2.052 6.583,2.198 0.438,0.146 10 false CANL 6.146,2.656 6.583,2.823 0.438,0.167 10 false CANH 4.135,1.917 4.406,2.083 0.271,0.167 10 false 39 4.135,2.51 4.365,2.688 0.229,0.177 10 false 40 5.875,1.927 6.135,2.115 0.26,0.188 10 false 22 5.875,2.531 6.115,2.719 0.24,0.188 10 false 13 5.865,3.542 6.073,3.75 0.208,0.208 10 false 25 5.875,4.135 6.104,4.323 0.229,0.188 10 false 26 6.146,3.656 6.354,3.813 0.208,0.156 10 false E1 6.146,4.26 6.385,4.427 0.24,0.167 10 false E2 5.875,0.74 6.052,0.885 0.177,0.146 10 false 21 6.146,0.854 6.5,1.01 0.354,0.156 10 false IG2 3.052,5.604 3.521,5.781 0.469,0.177 10 false G304 3.052,5.771 4.823,5.958 1.771,0.188 10 false Combination Meter 5.75,5.573 6.083,5.74 0.333,0.167 10 false G1 5.75,5.729 7.115,5.938 1.365,0.208 10 false Center Airbag Sensor 0.219,3.25 1.052,3.458 0.833,0.208 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Result
Result Proceed to
DTC is not output A
DTCs are output (w/ Central Gateway ECU) B
DTCs are output (w/o Central Gateway ECU) C



A

2.CHECK BATTERY

B

C

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V




OK

3.CHECK CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
U148229E03
1.615,1.365 1.271,1.896 true 1.76,1.375 2.135,1.885 true 2.24,1.333 2.615,1.333 true 0.406,0.813 0.667,0.969 0.26,0.156 10 false G1 1.177,1.927 1.427,2.115 0.25,0.188 10 false E2 2.125,1.906 2.354,2.073 0.229,0.167 10 false E1 2.719,1.24 3.01,1.406 0.292,0.167 10 false IG2 1.615,0.198 1.833,0.365 0.219,0.167 10 false *a

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG2) - G1-25 (E1) Ignition switch ON 11 to 14 V
G1-21 (IG2) - G1-26 (E2) Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor)



OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.

for 5L-E:

i.
U148230C01
1.25,1.438 0.958,1.875 true 0.792,1.448 0.521,1.844 true 1.458,1.438 2.031,1.865 true 0.271,1.229 0.49,1.385 0.219,0.156 10 false G6 0.792,1.802 0.927,1.958 0.135,0.156 10 false B 0.302,1.781 0.51,1.938 0.208,0.156 10 false E2 2.104,1.802 2.354,1.958 0.25,0.156 10 false IG+ 1.677,0.354 1.875,0.521 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to Combination Meter)


Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


ii.

Disconnect the G6 connector from the combination meter.


iii.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-28 (IG+) - G6-21 (E2) Ignition switch ON 11 to 14 V
G6-26 (B) - G6-21 (E2) Always 11 to 14 V




b.

except 5L-E:

i.
U148230C02
0.76,1.458 0.469,1.896 true 2.583,1.281 2.844,1.323 true 0.875,1.438 1.031,1.813 true 0.198,1.24 0.604,1.5 0.406,0.26 10 false G304 0.396,1.896 0.531,2.052 0.135,0.156 10 false B 2.885,1.25 3.156,1.427 0.271,0.177 10 false E2 0.938,1.823 1.188,1.979 0.25,0.156 10 false IG+ 1.677,0.354 1.875,0.521 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to Combination Meter)


Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


ii.

Disconnect the G304 connector from the combination meter.


iii.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-22 (IG+) - G304-20 (E2) Ignition switch ON 11 to 14 V
G304-21 (B) - G304-20 (E2) Always 11 to 14 V





OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG