Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E321781E56
3.396,0.115 3.833,0.354 0.438,0.24 3.448,0.146 4.063,0.344 0.615,0.198 10 false G224

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G224-7 (B) - G224-28 (GND) G - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G224-3 (BZ) - G224-28 (GND) SB - W-B Skid control buzzer assembly output Ignition switch ON, buzzer not sounding 11 to 14 V
Ignition switch ON, buzzer sounding Below 1 V
G224-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G224-8 (CA1P) - G224-28 (GND) GR - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
G224-9 (CA1N) - G224-28 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
G224-10 (CA2H) - G224-28 (GND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
G224-11 (CA2L) - G224-28 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between G224-8 (CA1P) - G224-28 (GND)
Between G224-10 (CA2H) - G224-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between G224-9 (CA1N) - G224-28 (GND)
Between G224-11 (CA2L) - G224-28 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


E321782E43
2.167,0.75 2.583,1 0.417,0.25 2.208,0.792 2.667,0.99 0.458,0.198 10 false A100

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-8 (IGB) - A100-1 (SGND) GR-G - BR Power source Ignition switch ON 11 to 14 V
A100-1 (SGND) - Body ground BR - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the millimeter wave radar sensor is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-3 (CA2H) - A100-1 (SGND) V - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A100-2 (CA2L) - A100-1 (SGND) W - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
A100-5 (CA1P) - A100-1 (SGND) L - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
A100-6 (CA1N) - A100-1 (SGND) W - BR CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between A100-3 (CA2H) and A100-1 (SGND)
Between A100-5 (CA1P) and A100-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between A100-2 (CA2L) and A100-1 (SGND)
Between A100-6 (CA1N) and A100-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.