Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (for 1GD-FTV) › from 2017.08
RM27T0E _55 Steering _053717 POWER ASSIST SYSTEMS _0260953 VANE PUMP(for 1GD-FTV) G

POWER ASSIST SYSTEMS  VANE PUMP(for 1GD-FTV)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16361A 1.INSPECT FAN AND GENERATOR V BELT

Hide 2.BLEED AIR FROM POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.

i.

Run the engine at idle for a few minutes.



f.

Turn the steering wheel.

i.

With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1


ii.

Repeat *1 several times.



g.

Stop the engine.


h.

Check for foaming or emulsification.

If the system has to be bled twice specifically because of foaming or emulsification, check for fluid leaks in the power steering system.


i.

Check the fluid level.


Hide 3.CHECK POWER STEERING FLUID LEVEL

a.

Keep the vehicle horizontal.


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF "DEXRON" II or III, or equivalent.


HINT:

If the fluid is hot (over 40°C (104°F)), make sure that the fluid level is within the HOT range on the reservoir. If the fluid is cold, make sure that it is within the COLD range.



c.

Start the engine and run it at idle.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



e.

Check for foaming or emulsification.

If foaming or emulsification is identified, bleed air from the power steering system.


f.
C106308E08
0.125,0.125 0.969,0.281 0.844,0.156 10 false *a 2.115,0.146 3.146,0.302 1.031,0.156 10 false *b 1.688,1.365 2.646,1.677 0.958,0.313 10 false *c

With the engine idling, measure the fluid level in the reservoir.

Text in Illustration
*a Engine Idling
*b Engine Stopped
*c 5 mm or less


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum increase in fluid level:

Approximately 5 mm (0.197 in.)


If the fluid level increase is more than the maximum, bleed air from the power steering system.


i.

Check the fluid level.


Hide 4.CHECK STEERING FLUID PRESSURE

a.

Disconnect the pressure feed tube from the vane pump.


b.
C327768E02
1.313,2.24 1.479,2.906 1.479,2.906 1.938,2.906 true 1.729,2.104 1.781,2.896 true 1.583,2.146 1.563,2.813 1.563,2.813 1.01,2.813 true 1.24,2.281 1.219,2.802 true 0.104,1 0.427,1.219 0.323,0.219 10 false *c 0.875,0.188 1.198,0.406 0.323,0.219 10 false *c 2.323,1.625 2.646,1.844 0.323,0.219 10 true *a 3.177,1.625 3.385,1.833 0.208,0.208 10 true *b 1.969,2.823 2.292,3.042 0.323,0.219 10 true *2 0.802,2.729 1.125,2.948 0.323,0.219 10 true *1

Connect SST as shown in the illustration.

SST
09640-10010  (09641-01010, 09641-01040, 09641-01070)

Text in Illustration
*1 Gasket
*2 Union Bolt
*a In
*b Out
*c Attachment

NOTICE:

Check that the valve of SST is in the open position.



c.

Bleed air from the power steering system.

NOTICE:

Check the level of power steering fluid and refill as necessary.



d.

Start the engine and run it at idle.


e.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



f.
C162692E02
2.17,0.392 3.174,0.780 1.004,0.387 10 *2 2.174,3.149 3.165,3.683 0.990,0.534 10 *3 0.108,1.775 1.107,2.147 0.999,0.372 10 *1 0.806,3.979 1.642,4.135 0.836,0.156 10 *a 1.892,2.647 2.215,2.816 0.323,0.170 10 SST 1.84,2.724 1.703,2.724 1.703,2.724 1.561,3.083 false

With the engine idling, close the valve of SST and observe the reading on SST.

Standard fluid pressure:

8800 to 9300 kPa (89.7 to 94.8 kgf/cm2, 1276 to 1348 psi)


Text in Illustration
*1 Power Steering Gear
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Closed

NOTICE:
·

Do not keep the valve closed for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is not as specified, check for fluid leaks and replace parts as necessary.


g.
C162693E02
2.165,0.416 3.143,0.760 0.979,0.344 10 *2 2.173,3.145 3.155,3.662 0.982,0.517 10 *3 0.11,1.653 1.111,2.007 1.001,0.355 10 *1 0.706,3.99 1.473,4.146 0.767,0.156 10 *a 1.875,2.628 2.197,2.798 0.323,0.170 10 SST 1.823,2.723 1.686,2.723 1.686,2.723 1.544,3.082 false

With the engine idling, open the valve fully.

Text in Illustration
*1 Power Steering Gear
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Open


h.

Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

Fluid pressure difference:

490 kPa (5.0 kgf/cm2, 71 psi) or less


NOTICE:

Do not turn the steering wheel.


If the pressure difference is not within the specified range, check for fluid leaks and replace parts as necessary.


i.
C162694E02
2.152,0.385 3.141,0.744 0.989,0.358 10 *2 2.173,3.135 3.142,3.645 0.969,0.511 10 *3 0.111,1.664 1.140,2.173 1.029,0.509 10 *1 0.702,4.007 1.538,4.162 0.836,0.156 10 *a 1.871,2.638 2.193,2.808 0.323,0.170 10 SST 1.819,2.73 1.681,2.73 1.681,2.73 1.515,3.089 false

With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

Standard fluid pressure:

8800 to 9300 kPa (89.7 to 94.8 kgf/cm2, 1276 to 1348 psi)


Text in Illustration
*1 Power Steering Gear (Lock Position)
*2 Power Steering Fluid Reservoir
*3 Power Steering Vane Pump
*a Valve Open

NOTICE:
·

Do not keep the steering wheel in the full lock position for more than 10 seconds.

·

Do not allow the fluid temperature to become too high.



If the pressure is not as specified, check for fluid leaks and replace parts as necessary.


j.

Disconnect SST.


k.

Connect the pressure feed tube to the vane pump.


l.

Bleed air from the power steering system.

NOTICE:

Check the level of power steering fluid and refill as necessary.