Home › Steering › STEERING COLUMN › STEERING SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260956 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING OFF CENTER ADJUSTMENT PROCEDURE

HINT:

This is the adjustment procedure for when the steering is off center.


a.

Check if the steering wheel is off center.

i.
C384098N01
1.854,0.365 2.052,0.365 2.052,0.365 2.302,0.729 true 1.281,0.802 1.99,0.802 1.99,0.802 2.24,1.167 true 1.656,0.813 2.073,1.365 true 1.344,1.896 1.604,1.896 1.604,1.896 1.969,1.542 true 1.104,0.719 1.417,0.917 0.313,0.198 10 false *a 1.677,0.26 1.99,0.458 0.313,0.198 10 false *1 1.177,1.823 1.49,2.021 0.313,0.198 10 false *2

Apply masking tape to the top center of the steering wheel and steering column upper cover.

Text in Illustration
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Masking Tape


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph) and hold the steering wheel to maintain course.


iii.
C384099N01
1.479,0.531 1.729,0.531 1.729,0.531 2.083,0.927 true 1.448,1.927 1.646,1.927 1.646,1.927 2.073,1.635 true 1.469,1.083 2.073,1.083 2.073,1.083 2.427,1.271 true 1.75,1.094 2.438,1.542 true 1.271,0.438 1.583,0.635 0.313,0.198 10 false *2 1.24,1.833 1.552,2.031 0.313,0.198 10 false *1 1.229,1 1.542,1.198 0.313,0.198 10 false *a

Draw a line on the masking tape as shown in the illustration.

Text in Illustration
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Marked Line


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C384100N01
1.563,0.479 1.833,0.479 1.833,0.479 2,0.854 false 1.563,1.896 1.719,1.896 1.719,1.896 1.958,1.625 false 1.354,1 2.052,1 2.052,1 2.375,1.219 true 1.583,1 2.385,1.531 true 1.344,0.396 1.656,0.594 0.313,0.198 10 false *2 1.354,1.823 1.667,2.021 0.313,0.198 10 false *1 1.146,0.917 1.458,1.115 0.313,0.198 10 false *a

Draw a new line on the masking tape on the steering wheel as shown in the illustration.

Text in Illustration
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Marked Line


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to a steering angle value.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1°.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C170785E02
2.04,0.149 2.285,0.328 0.246,0.178 10 *a 1.181,0.791 1.847,0.235 false 1.377,0.845 1.847,0.235 1.847,0.235 1.998,0.235 false

Place matchmarks RH and LH tie rod ends and rack ends respectively where it can be easily seen.

Text in Illustration
*a Matchmark


ii.

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.
C145857

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle value

HINT:

One 360° turn of a rack end (1.5 mm (0.0591 in.) horizontal movement) is equal to a 12° change in steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH boot clips.