Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053743 SLIDING ROOF / CONVERTIBLE _0261242 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof Control Switch Circuit  


DESCRIPTION

The sliding roof drive gear sub-assembly (sliding roof ECU) receives each signal when the map light assembly (slide roof switch) is operated and drives its built-in motor.

WIRING DIAGRAM

B450497E04
0.198,0.052 1.104,0.406 0.906,0.354 10 false from IG1 NO.1 Relay*1 2.073,0.792 2.958,0.99 0.885,0.198 10 false ECU-IG NO.2 0.615,4.615 3.208,4.823 2.594,0.208 10 false Map Light Assembly (Sliding Roof Switch) 0.604,4.448 1.063,4.646 0.458,0.198 10 false W7 4.729,4.635 6,4.833 1.271,0.198 10 false Sliding Roof ECU 3.958,5.385 6.354,5.615 2.396,0.229 10 false Sliding Roof Drive Gear Sub-assembly 3.958,5.208 4.417,5.406 0.458,0.198 10 false W20 6.24,2.313 6.677,2.813 0.438,0.5 10 false Sliding Roof Motor 2.51,2.813 2.885,3.01 0.375,0.198 10 false OPN 2.594,1.479 2.885,1.677 0.292,0.198 10 false UP 2.385,2.146 2.844,2.344 0.458,0.198 10 false DOWN 2.531,3.51 2.99,3.708 0.458,0.198 10 false CLS 3.792,2.156 4.25,2.354 0.458,0.198 10 false DWN 3.792,1.479 4.083,1.677 0.292,0.198 10 false UP 3.781,3.51 4.24,3.708 0.458,0.198 10 false CLS 3.792,2.802 4.281,3.042 0.49,0.24 10 false OPN 3.813,0.5 4.104,0.698 0.292,0.198 10 false IG 3.573,0.49 3.729,0.688 0.156,0.198 10 false 1 3.594,2.813 3.75,3.01 0.156,0.198 10 false 7 3.573,3.5 3.729,3.698 0.156,0.198 10 false 5 3.583,2.146 3.74,2.344 0.156,0.198 10 false 6 3.573,1.479 3.729,1.677 0.156,0.198 10 false 4 2.896,3.5 3.115,3.698 0.219,0.198 10 false 28 2.896,2.823 3.208,3.021 0.313,0.198 10 false 27 2.906,2.146 3.219,2.344 0.313,0.198 10 false 25 2.906,1.469 3.219,1.667 0.313,0.198 10 false 24 3.802,4 4.094,4.198 0.292,0.198 10 false E 3.521,4 3.833,4.198 0.313,0.198 10 false 12 0.833,3.51 1.448,3.708 0.615,0.198 10 false GND3 0.583,3.51 0.74,3.708 0.156,0.198 10 false 5 1.854,1.76 2.146,1.958 0.292,0.198 10 false UP 1.74,2.458 2.198,2.656 0.458,0.198 10 false DOWN 1.75,3.115 2.167,3.313 0.417,0.198 10 false OPEN 1.729,3.792 2.25,3.99 0.521,0.198 10 false CLOSE 0.188,0.625 1.063,0.979 0.875,0.354 10 false from IG NO.1 Relay*2 0.229,5.083 0.99,5.281 0.76,0.198 10 false *1: for 5L-E 0.229,5.375 1.365,5.573 1.135,0.198 10 false *2: except 5L-E

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SLIDING ROOF)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Slide Roof Operate sliding roof Opn/Dwn: Sliding roof slide open or tilt down operation occurs
Clos/Up: Sliding roof slide close or tilt up operation occurs
OFF: Sliding roof not operating
-

OK:

The sliding roof operates normally.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

2.READ VALUE USING GTS (SLIDING ROOF)
2.READ VALUE USING GTS (SLIDING ROOF)
a.

Using the GTS, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Slide open switch signal / ON or OFF ON: Slide open switch pressed
OFF: Slide open switch not pressed
-
Close Switch Slide close switch signal / ON or OFF ON: Slide close switch pressed
OFF: Slide close switch not pressed
-
Up Switch Tilt up switch signal / ON or OFF ON: Tilt up switch pressed
OFF: Tilt up switch not pressed
-
Down Switch Tilt down switch signal / ON or OFF ON: Tilt down switch pressed
OFF: Tilt down switch not pressed
-

OK:

The GTS display changes according to switch operation as shown in the table.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
B240415E11
0.823,1.396 0.427,0.885 false 1.865,1.802 1.656,1.26 false 2.302,1.802 2.042,1.25 false 1.24,1.375 1.313,0.604 false 0.958,1.385 0.885,0.677 false 1.354,1.385 1.927,0.635 false 1.51,1.396 1.26,1.833 false 0.135,0.042 0.385,0.219 0.25,0.177 10 false *a 1.823,1.823 2.052,2 0.229,0.177 10 false IG 2.323,1.813 2.75,1.99 0.427,0.177 10 false GND3 1.177,1.854 1.521,2.031 0.344,0.177 10 false IG3 0.604,0.458 0.979,0.635 0.375,0.177 10 false OPN 0.115,0.677 0.469,0.854 0.354,0.177 10 false CLS 1.135,0.385 1.625,0.563 0.49,0.177 10 false DOWN 1.958,0.448 2.198,0.625 0.24,0.177 10 false UP

a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (IG) - 23 (IG3) Always Below 1 Ω
24 (UP) - 5 (GND3) Tilt up switch pressed Below 1 Ω
24 (UP) - 5 (GND3) Tilt up switch not pressed 10 kΩ or higher
25 (DOWN) - 5 (GND3) Tilt down switch pressed Below 1 Ω
25 (DOWN) - 5 (GND3) Tilt down switch not pressed 10 kΩ or higher
27 (OPN) - 5 (GND3) Slide open switch pressed Below 1 Ω
27 (OPN) - 5 (GND3) Slide open switch not pressed 10 kΩ or higher
28 (CLS) - 5 (GND3) Slide close switch pressed Below 1 Ω
28 (CLS) - 5 (GND3) Slide close switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Map Light Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)
B295816E07
0.417,1.063 0.885,1.313 0.469,0.25 2.5,1.75 2.25,1.75 2.25,1.75 2.135,1.417 true 0.833,0.708 1.083,0.708 1.083,0.708 1.281,1.135 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 0.5,1.115 0.854,1.302 0.354,0.188 10 false W20 0.677,0.646 0.958,0.833 0.281,0.188 10 false IG 2.542,1.677 2.823,1.865 0.281,0.188 10 false E

a.

Disconnect the W20 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W20-12 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
W20-1 (IG) - Body ground Ignition switch ON 11 to 14 V
W20-1 (IG) - Body ground Ignition switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly)


OK

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - MAP LIGHT ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - MAP LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the W20 ECU connector.


b.

Disconnect the W7 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W20-4 (UP) - W7-24 (UP) Always Below 1 Ω
W20-5 (CLS) - W7-28 (CLS) Always Below 1 Ω
W20-6 (DWN) - W7-25 (DOWN) Always Below 1 Ω
W20-7 (OPN) - W7-27 (OPN) Always Below 1 Ω
W7-5 (GND3) - Body ground Always Below 1 Ω
W20-12 (E) - Body ground Always Below 1 Ω
W20-4 (UP) or W7-24 (UP) - Body ground Always 10 kΩ or higher
W20-5 (CLS) or W7-28 (CLS) - Body ground Always 10 kΩ or higher
W20-6 (DWN) or W7-25 (DOWN) - Body ground Always 10 kΩ or higher
W20-7 (OPN) or W7-27 (OPN) - Body ground Always 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR