Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd start mode is selected with the combination switch assembly (2nd start), the TCM controls the solenoid valves and the transmission starts from 2nd gear.

In 2nd start mode, the system operates the throttle motor to control engine output to reduce skidding of the drive wheels and guarantee stable acceleration from rest, straight driving and turning stability.

When the shift lever is in D, the transmission automatically shifts up from 2nd to 5th as usual.

HINT:
·

The combination switch assembly (2nd start) is a momentary-type switch.

·

In order to cancel 2nd start mode, push the combination switch assembly (2nd start) again or turn the ignition switch off.



WIRING DIAGRAM

C214971E12
2.5,2.302 3.063,2.5 0.563,0.198 10 false G156 2.542,1.583 2.938,1.781 0.396,0.198 10 false E 3.531,1.583 3.927,1.781 0.396,0.198 10 false 2ND 3.948,1.854 4.344,2.052 0.396,0.198 10 false 14 5.813,2.906 6.313,3.104 0.5,0.198 10 false G70 5.813,3.083 6.313,3.281 0.5,0.198 10 false TCM 5.635,1.688 6.135,1.885 0.5,0.198 10 false SNWI 5.323,1.833 5.563,2.031 0.24,0.198 10 false 13 2.271,1.854 2.667,2.052 0.396,0.198 10 false 24 2.5,2.49 3.833,2.896 1.333,0.406 10 false Combination Switch Assembly (2nd Start)

PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY (2ND START)
a.
C331272E27
2.156,1.781 2.385,1.281 true 0.542,1.76 0.833,1.292 true 2.042,1.823 2.5,2.021 0.458,0.198 10 false 2ND 0.458,1.802 0.615,2 0.156,0.198 10 false E 0.208,0.125 0.521,0.323 0.313,0.198 10 false *1

Remove the combination switch assembly (2nd start) (See pageDrivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) 2ND START switch pushed and held Below 1 Ω
14 (2ND) - 24 (E) 2ND START switch not pushed 10 kΩ or higher


Text in Illustration
*1 Combination Switch Assembly (2nd Start)


Result:
Result Proceed to
OK A
NG (w/ Module Switch) B
NG (w/o Module Switch) C


A

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - BODY GROUND)

B

REPLACE COMBINATION SWITCH ASSEMBLY (w/ Module Switch (2nd Start))

C

REPLACE NO. 2 COMBINATION SWITCH ASSEMBLY (w/o Module Switch (2nd Start))

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - BODY GROUND)
a.
U157694E05
2.865,1.844 2.646,1.365 true 1.552,0.24 2.167,0.438 0.615,0.198 10 false G156 2.875,1.906 3.094,2.156 0.219,0.25 10 false E 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a

Disconnect the G156 combination switch assembly (2nd start) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-24 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Switch Assembly (2nd Start))



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - TCM)
a.
U169988E02
2.396,2.073 1.917,2.406 false 1.5,2.448 2.208,2.635 0.708,0.188 10 false 13 (SNWI) 0.083,0.042 0.292,0.229 0.208,0.188 10 false *a 2.323,0.375 2.635,0.552 0.313,0.177 10 false G70

Disconnect the G70 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G70-13 (SNWI) - Body ground 2ND START switch switch pushed and held Below 1 Ω
G70-13 (SNWI) - Body ground 2ND START switch switch not pushed 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR