Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is output when LIN communication between the certification ECU and ID code box stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2789 No communication between the certification ECU and ID code box for 10 seconds or more.
·

ID code box

·

Certification ECU

·

Harness or connector



WIRING DIAGRAM

C358547E02
0.958,1.208 1.417,1.406 0.458,0.198 10 false G215 0.958,1.365 2.073,1.604 1.115,0.24 10 false Certification ECU 1.542,0.625 2,0.823 0.458,0.198 10 false LIN 5.365,0.625 5.823,0.823 0.458,0.198 10 false LIN1 1.906,0.5 2.219,0.698 0.313,0.198 10 false 6 5.125,0.479 5.281,0.677 0.156,0.198 10 false 2 3.083,1.031 3.906,1.26 0.823,0.229 10 false from Battery 4.51,1.208 5.042,1.427 0.531,0.219 10 false SMART 5.354,1.031 5.667,1.229 0.313,0.198 10 false +B 5.365,1.49 5.823,1.688 0.458,0.198 10 false GND 5.219,2 5.677,2.198 0.458,0.198 10 false G207 5.229,2.177 6.125,2.385 0.896,0.208 10 false ID Code Box 5.125,0.927 5.281,1.125 0.156,0.198 10 false 1 5.125,1.385 5.281,1.583 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the ID code box and certification ECU stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2789 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
a.

Disconnect the G215 certification ECU connector.


b.

Disconnect the G207 ID code box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-6 (LIN) - G207-2 (LIN1) Always Below 1 Ω
G215-6 (LIN) or G207-2 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX - BATTERY AND BODY GROUND)
a.
B301231E05
1.51,0.25 1.979,0.51 0.469,0.26 0.729,1.604 1.229,1.354 true 2.688,1.604 2.188,1.354 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.542,1.563 0.854,1.76 0.313,0.198 10 false +B 1.583,0.292 2.073,0.49 0.49,0.198 10 false G207 2.74,1.552 3.052,1.75 0.313,0.198 10 false GND

Disconnect the G207 ID code box connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G207-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G207-1 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to ID Code Box)


OK

5.REPLACE ID CODE BOX

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX
a.

Temporarily replace the ID code box with a new one.



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2789 is not output.




OK

END (ID CODE BOX IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU