Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261300 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 89997 1.INSTALL ELECTRICAL KEY ANTENNA (w/ Entry and Start System)

a.

Install the electrical key antenna with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52186B 2.INSTALL REAR BUMPER SIDE MOUNTING BRACKET LH

a.

w/ Entry and Start System:

Connect the connector.


b.

Install the rear bumper side mounting bracket LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52185B 3.INSTALL REAR BUMPER SIDE MOUNTING BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 52158C 4.INSTALL REAR BUMPER NO. 2 SIDE SUPPORT LH

a.

Install the rear bumper No. 2 side support LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52174D 5.INSTALL REAR BUMPER BAR REINFORCEMENT LH

a.

Install the rear bumper bar reinforcement LH with the 3 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 52173D 6.INSTALL REAR BUMPER BAR REINFORCEMENT RH

HINT:

Use the same procedure described for the LH side.


Hide 52156A 7.INSTALL REAR BUMPER SIDE SUPPORT LH

a.

Attach the 4 claws to install the rear bumper side support LH.


b.

Install the 3 screws.


Hide 52155A 8.INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52169A 9.INSTALL REAR BUMPER NO. 3 SIDE SUPPORT

a.

Install the rear bumper No. 3 side support with the screw.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 52159 10.INSTALL REAR BUMPER COVER

a.

w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:

Connect the 3 connectors.


b.

w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light:

Connect the connector.


c.

w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light:

Connect the 2 connectors.


d.
B490893

Set the rear bumper cover on the vehicle as shown in the illustration.


e.
B488283

Attach the 7 claws to install the rear bumper cover.

HINT:

Use the same procedure to attach the claw on the other side.



f.

Remove the protective tape.


g.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Install the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.

Install the 2 clips.


Hide 52162B 11.INSTALL REAR BUMPER NO. 1 PLATE

a.

Attach the 21 claws to install the rear bumper No. 1 plate.

B488279


b.

Remove the protective tape.


c.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52179B 12.INSTALL REAR BUMPER BAR PLATE

a.

Attach the 14 claws to install the rear bumper bar plate.

B488277


b.

Remove the protective tape.


Hide 58766A 13.INSTALL JACK BOX HOLE COVER

a.

Attach the 2 claws to install the jack box hole cover.


Hide 76626E 14.INSTALL REAR QUARTER PANEL MUDGUARD LH

Hide 76625G 15.INSTALL REAR QUARTER PANEL MUDGUARD RH

HINT:

Use the same procedure described for the LH side.