Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRAPHIC DECAL(for 5 Door) › from 2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261315 GRAPHIC DECAL(for 5 Door) A

EXTERIOR PANELS / TRIM  GRAPHIC DECAL(for 5 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) per second.

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



B200106C10
0.104,0.115 3.417,1.615 3.313,1.5 2.344,0.281 2.281,0.281 2.281,0.281 2.135,0.74 false 1.417,1.156 1.417,1.344 false 0.833,0.49 0.677,0.615 false 1.865,3.521 2.01,3.521 false 5.427,3.458 5.573,3.458 false 1.531,3.094 1.688,3.229 false 4.781,3.125 5.177,3.198 false 0.167,0.156 0.396,0.417 0.229,0.26 10 *a 2.396,0.208 2.729,0.49 0.333,0.281 10 *b 1.344,1.354 1.542,1.594 0.198,0.24 10 *c 0.875,0.396 1.135,0.646 0.26,0.25 10 *d 0.083,1.708 0.365,1.979 0.281,0.271 12 *A 3.948,1.698 4.292,1.958 0.344,0.26 12 *B 2.063,1.823 2.24,2.052 0.177,0.229 10 C 5.417,2.583 5.646,2.833 0.229,0.25 10 D 1.688,3.427 1.875,3.677 0.188,0.25 10 *e 5.26,3.375 5.479,3.604 0.219,0.229 10 *e 1.375,3 1.563,3.281 0.188,0.281 10 *1 1.115,2.385 1.385,2.646 0.271,0.26 10 B 4.583,2.365 4.844,2.646 0.26,0.281 10 B 2.813,2.573 2.969,2.771 0.156,0.198 10 A 6.292,2.229 6.438,2.479 0.146,0.25 10 A 4.615,3.031 4.802,3.26 0.188,0.229 10 *1
*A Pressing Forward *B Pulling
*1 Stripe Tape - -
*a Side View *b Non-padded Side
*c Padded Side *d Squeegee
*e Release Paper - -


Standard Measurement:
Area Measurement Area Measurement
A 10 to 20 mm (0.394 to 0.787 in.) B 30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
C 40 to 50° (for pressing forward) D 30 to 45° (for pulling)




f.
B147253C13
1.188,0.708 0.844,0.25 false 0.844,1 1.115,1.271 0.271,0.271 10 *e 1.396,0.521 1.656,0.771 0.26,0.25 10 *d 2.01,0.479 2.26,0.76 0.25,0.281 10 *c 0.677,0.146 0.938,0.396 0.26,0.25 10 *a 1.552,1.823 1.896,2.083 0.344,0.26 10 *b
*a Squeegee
*b Hem
*c First
*d Second
*e Third


Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75982B 2.INSTALL FENDER STRIPE LH

HINT:

When installing the fender stripe LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


B488306C01
0.948,1.313 1.146,1.313 false 2.531,1.365 2.531,1.177 false 1.188,1.229 1.5,1.427 0.313,0.198 10 false *c 2.479,1.365 2.792,1.563 0.313,0.198 10 false *c 0.458,1.177 0.771,1.375 0.313,0.198 10 false *a 2.438,0.656 2.75,0.854 0.313,0.198 10 false *b
*a 4.7 mm (0.185 in.)
*b 3.0 mm (0.118 in.)
*c R End


a.

Refer to the illustration to position a new fender stripe LH.


b.

Remove the application sheet from the fender stripe LH.


Hide 75974F 3.INSTALL FRONT SIDE PANEL STRIPE LH

HINT:

When installing the front side panel stripe LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


B488308C01
0.625,1.219 0.625,1.448 false 1.688,1.24 1.688,1.469 false 2.656,0.792 2.49,0.792 true 1.375,3.375 1.531,3.375 true 2.542,3.563 2.688,3.563 2.688,3.563 2.688,3.802 false 3.052,3.813 3.052,4.042 true 0.594,0.698 0.906,0.896 0.313,0.198 10 false *a 1.552,0.75 1.865,0.948 0.313,0.198 10 false *b 2.979,0.802 3.292,1 0.313,0.198 10 false *c 1.813,3.458 2.125,3.656 0.313,0.198 10 false *d 2.635,4.031 2.948,4.229 0.313,0.198 10 false *e 2.948,3.365 3.26,3.563 0.313,0.198 10 false *f 0.563,1.438 0.875,1.635 0.313,0.198 10 false *g 1.615,1.458 1.927,1.656 0.313,0.198 10 true *g 2.333,0.698 2.563,0.948 0.229,0.25 10 false *g 1.219,3.292 1.448,3.542 0.229,0.25 10 false *g 2.385,3.479 2.615,3.729 0.229,0.25 10 false *g 2.979,4.042 3.208,4.292 0.229,0.25 10 false *g
*a 3.0 mm (0.1181 in.)
*b 5.0 mm (0.197 in.)
*c 5.0 mm (0.197 in.)
*d 5.0 mm (0.197 in.)
*e 3.0 mm (0.118 in.)
*f 3.0 mm (0.118 in.)
*g R End


a.

Refer to the illustration to position a new front side panel stripe LH.


b.

Remove the application sheet from the front side panel stripe LH.


Hide 75997C 4.INSTALL REAR BODY STRIPE LH

HINT:

When installing the rear body stripe LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


B488310C01
0.792,1.333 0.552,1.573 false 1.823,0.646 1.427,0.844 false 2.875,0.896 2.99,1.063 true 0.75,0.833 1.01,1.031 0.26,0.198 10 false *a 0.385,1.49 0.604,1.708 0.219,0.219 10 false *d 1.781,0.948 2.042,1.146 0.26,0.198 10 false *b 2.74,0.365 3.052,0.521 0.313,0.156 10 false *c 1.875,0.573 2.188,0.729 0.313,0.156 10 false *d 2.958,1.073 3.271,1.229 0.313,0.156 10 false *d
*a 3.0 mm (0.118 in.)
*b 6.7 mm (0.264 in.)
*c 3.0 mm (0.118 in.)
*d R End


a.

Refer to the illustration to position a new rear body stripe LH.


b.

Remove the application sheet from the rear body stripe LH.


Hide 75994D 5.INSTALL REAR UPPER QUARTER STRIPE LH

HINT:

When installing the rear upper quarter stripe LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


B488312C01
0.604,1.01 0.698,1.135 true 1.813,0.896 2.01,0.896 true 2.771,0.844 2.625,0.948 true 0.521,0.49 0.76,0.708 0.24,0.219 10 false *a 1.365,0.823 1.583,1.021 0.219,0.198 10 false *b 2.708,0.313 2.927,0.531 0.219,0.219 10 false *c 0.646,1.135 0.875,1.344 0.229,0.208 10 false *d 2.031,0.813 2.26,1.021 0.229,0.208 10 false *d 2.521,0.948 2.75,1.156 0.229,0.208 10 false *d
*a 3.0 mm (0.118 in.)
*b 8.0 mm (0.315 in.)
*c 5.0 mm (0.197 in.)
*d R End


a.

Refer to the illustration to position a new rear upper quarter stripe LH.


b.

Remove the application sheet from the rear upper quarter stripe LH.


Hide 75992A 6.INSTALL QUARTER STRIPE LH

HINT:

When installing the quarter stripe LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


B488314C01
0.552,1.156 0.792,0.979 0.792,0.979 0.594,1.167 true 1.615,0.781 1.406,0.719 false 3.083,0.781 2.906,0.896 true 2.75,3.573 2.594,3.719 true 0.427,0.719 0.667,0.958 0.24,0.24 10 false *a 0.552,1.552 0.865,1.708 0.313,0.156 10 false *b 1.885,0.844 2.115,1.042 0.229,0.198 10 false *c 2.448,0.781 2.667,0.958 0.219,0.177 10 false *d 2.688,3.083 2.938,3.292 0.25,0.208 10 false *e 0.833,0.906 1.094,1.125 0.26,0.219 10 false *f 1.271,0.625 1.531,0.844 0.26,0.219 10 false *f 3.125,0.708 3.385,0.927 0.26,0.219 10 false *f 2.51,3.729 2.771,3.948 0.26,0.219 10 false *f
*a 3.0 mm (0.118 in.)
*b 3.0 mm (0.118 in.)
*c 4.7 mm (0.185 in.)
*d 3.0 mm (0.118 in.)
*e 4.8 mm (0.189 in.)
*f R End


a.

Refer to the illustration to position a new quarter stripe LH.


b.

Remove the application sheet from the quarter stripe LH.