Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0327508 FRONT CAMERA A

CRUISE CONTROL  FRONT CAMERA  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, replace it with a new one.

·

Do not touch the camera lens or the front windshield glass in front of the camera.

·

If the forward recognition camera has been struck or dropped, replace it with a new one.

·

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, forward recognition camera system, lane departure alert system, road sign assist system or pre-crash safety system may not operate properly due to a difference in the transmissivity or black ceramic border.

·

w/ Camera Heater: Do not touch the internal components of the forward recognition with heater hood sub-assembly or press on the heater when working on the forward recognition with heater hood sub-assembly.



PROCEDURE

Hide 86466E 1.REMOVE NO. 2 FORWARD RECOGNITION COVER

a.
B485916N01
0.573,4.156 1.031,4.354 0.458,0.198 10 false (1) 2.177,4.167 2.635,4.365 0.458,0.198 10 false (2)

Detach the 2 claws in the direction indicated by the arrow (1) in the illustration.

NOTICE:

If the 2 claws are detached separately they may become damaged. Therefore, remove them at the same time.



b.

Detach the 2 guides in the direction indicated by the arrow (2) in the illustration to remove the No. 2 forward recognition cover.


Hide 86466D 2.REMOVE NO. 1 FORWARD RECOGNITION COVER

a.
B485917

Detach the 2 clips and 2 guides and remove the No. 1 forward recognition cover as shown in the illustration.

NOTICE:

When removing, press the cover parallel to the windshield glass surface and remove.



Hide 86464A 3.REMOVE FORWARD RECOGNITION LATCH

a.
B485918N01
2.042,2.604 2.281,2.802 0.24,0.198 10 true (1) 0.729,4.313 1.188,4.51 0.458,0.198 10 false (2)

Detach the 2 claws in the direction indicated by the arrow (1) in the illustration.


b.

Detach the 4 guides in the direction indicated by the arrow (2) in the illustration to remove the forward recognition latch.


Hide 8646C 4.REMOVE FORWARD RECOGNITION CAMERA

NOTICE:

If the forward recognition camera has been struck or dropped, replace it with a new one.


a.
B485919

Disconnect the connector.

NOTICE:

Do not pull the harness forcibly when disconnecting the connector.



b.

Detach the 4 guides and remove the forward recognition camera as shown in the illustration.

NOTICE:
·

Do not apply excessive force.

·

If the forward recognition camera bracket is deformed or damaged, replace it together with the windshield glass.




Hide 86401 5.REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Camera Heater)

NOTICE:
B485920

Do not touch the internal components of the forward recognition with heater hood sub-assembly or press on the heater when working on the forward recognition with heater hood sub-assembly.


a.
B485921

Disconnect the connector.

NOTICE:

Do not pull the harness forcibly when disconnecting the connector.



b.
B485922

Detach the connector clamp.


c.
B485923N01
0.854,3.677 1.313,3.875 0.458,0.198 10 false (1) 1.531,3.531 1.833,3.729 0.302,0.198 10 true (2) 1.125,3.927 1.583,4.125 0.458,0.198 10 false (3) 1.448,4.052 1.906,4.25 0.458,0.198 10 false (4) 2.052,4.344 2.51,4.542 0.458,0.198 10 false (5) 2.656,4.146 3,4.302 0.344,0.156 10 false (6) 3.083,3.833 3.396,4.031 0.313,0.198 10 false (7)

Detach the 7 guides in the order shown in the illustration and remove the wire harness.


d.
B485924C02
1.365,1.063 1.604,1.292 0.24,0.229 10 true (1) 1.896,1.719 2.354,1.917 0.458,0.198 10 false (2)
V100155

Heater Area


Detach the 2 claws in the direction indicated by the arrow (1) in the illustration.

NOTICE:

Do not press the heater area.



e.

Detach the guide in the direction indicated by the arrow (2) in the illustration to remove the forward recognition with heater hood sub-assembly.