FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus wires (communication wires), a fail-safe function(s) operates. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
Effects on each system when communication is impossible (for further details, see the pages for each system).
| Function
(Function Description) |
1.
Control Master 2.
System Related |
Behavior in Communication Failure | User Notification | Diagnostic Trouble Code |
|---|---|---|---|---|
| High-Low Switching Limitation
(Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.) |
1.
4 wheel drive control ECU 2.
ECM, Brake actuator assembly (skid control ECU) |
High-Low switching is prohibited. | The 4WD indicator light blinks and the buzzer sounds. | - |
| Center Differential Lock Switching Limitation
(Prohibits center differential lock switching when the difference in wheel speeds is large.) |
1.
4 wheel drive control ECU 2.
Brake actuator assembly (skid control ECU) |
Prohibits center differential lock switching. | The 4WD indicator light blinks and the buzzer sounds. | - |
| Rear Differential Lock Switching Limitation
(Prohibits rear differential lock switching when the vehicle speed is outside the acceptable range.) |
1.
ECM 2.
Brake actuator assembly (skid control ECU) |
Rear differential lock switching is prohibited. | The 4WD indicator light blinks. | - |
| L4F Switching Limitation
(Prohibits switching to L4F when VSC is malfunctioning.) |
1.
4 wheel drive control ECU 2.
Brake actuator assembly (skid control ECU) |
L4F switching is prohibited. | The 4WD indicator light blinks. | - |
| Specialized Control During Wheel Speed Failure
(When there is abnormal wheel speed, this control permits switching only when specified conditions are met (not all wheel speeds are abnormal, the brakes are applied, the engine speed is low and all normal wheel speeds are low).) |
1.
4 wheel drive control ECU 2.
ECM, Brake actuator assembly (skid control ECU) |
When all 4 wheels are malfunctioning, switching is prohibited. | The indicator lights blink quickly. | - |
| Indicator/Buzzer Signal Output
(Outputs a signal indicating the indicator and buzzer state, which are used to determine the actuator position and switching status.) |
1.
4 wheel drive control ECU 2.
Combination meter assembly |
State signal update is not possible. | Nothing | - |
| H-L Actuator Failure Signal Output
(Outputs a signal when the H-L actuator switch is malfunctioning.) |
1.
4 wheel drive control ECU 2.
ECM, Brake actuator assembly (skid control ECU), Combination meter assembly |
State signal update is not possible. | The indicator lights blink quickly. | - |
| L4 State Signal Output
(Outputs a signal when switching to the L4 position is finished.) |
1.
4 wheel drive control ECU 2.
Brake actuator assembly (skid control ECU), Combination meter assembly |
State signal update is not possible. | The status of the indicator lights change in accordance with changes in the L4 state signal. | - |
| Center Differential Lock State Signal Output
(Outputs the center differential lock P/S state.) |
1.
4 wheel drive control ECU 2.
Combination meter assembly |
State signal update is not possible. | The status of the indicator lights change in accordance with changes in the center differential lock state signal. | - |
| Rear Differential Lock State Signal Output
(Outputs the rear differential P/S state.) |
1.
4 wheel drive control ECU 2.
Combination meter assembly |
State signal update is not possible. | The status of the indicator lights change in accordance with changes in the rear differential lock state signal. | - |
| Signal Output During Switching
(Outputs the actuator switching state.) |
1.
4 wheel drive control ECU 2.
Combination meter assembly |
State signal update is not possible. | The indicator lights blink during signal output during switching. | - |
| ABS
(Prevents the wheels from locking when stopping suddenly.) |
1.
Brake actuator assembly (skid control ECU) 2.
Airbag sensor assembly |
The ABS does not operate. | The light illuminates. | ·
U0073 ·
U0114 ·
U0124 |
| Speedometer
(Controls the speedometer according to the vehicle speed signals.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
0 km/h (0 mph) is indicated. | Nothing | - |
| Tachometer
(Controls the tachometer according to the engine speed signals.) |
1.
Combination meter assembly 2.
ECM |
0 rpm is indicated. | Nothing | - |
| Engine Coolant Temperature Gauge
(Controls the temperature gauge according to the temperature signals.) |
1.
Combination meter assembly 2.
ECM |
The temperature gauge needle is at the middle of the "C" mark or below. | Nothing | - |
| Fuel Gauge
(Controls the fuel gauge according to the vehicle condition determined by the ST signal, vehicle speed signal and fuel amount.) |
1.
Combination meter assembly 2.
ECM, Brake actuator assembly (skid control ECU) |
·
When communication is lost with the main body ECU: -
Operates with the parking brake released. -
Ignition switch is off. ·
When communication is lost with a device other than the main body ECU: -
Operates the same as when the vehicle is stopped. -
Operates with starter off. |
Nothing | - |
| ODO/TRIP Meter
(Calculates and indicates the driven distance according to the pulse count of the vehicle speed pulse signal.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
The calculation stops and the last displayed value remains. | Nothing | - |
| Telltale
(Controls indicator illumination and blinking according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
Airbag sensor assembly |
- | ·
The SRS warning light illuminates. ·
The status of the front passenger side seat belt warning light is maintained. |
- |
1.
Combination meter assembly 2.
Main body ECU (multiplex network body ECU) |
- | ·
The status of the following indicators (warning lights) is maintained when the ignition switch is ON and turn off when the ignition switch is turned off: -
Beam indicator light -
HEAD indicator light -
Tail indicator light -
Open door warning light -
Driver side seat belt warning light -
Brake warning light -
Front fog indicator light -
Rear fog indicator light |
- | |
| Telltale
(Controls indicator illumination and blinking according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
ECM |
- | ·
The status of the following indicators (warning lights) is maintained when the ignition switch is ON and turn off when the ignition switch is turned off: -
Charge warning light -
Glow indicator light ·
The following indicators turn off: Eco driving indicator light |
- |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
- | ·
The following indicators (warning lights) turn on: -
Brake warning light -
ABS warning light ·
The speed limit indicator light turns off. |
- | |
| Telltale
(Controls indicator illumination and blinking according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
4 wheel drive control ECU |
- | ·
The status of the following indicators (warning lights) is maintained when the ignition switch is ON and turn off when the ignition switch is turned off: -
Center differential lock indicator -
Rear differential lock indicator light -
4LO indicator light |
- |
| Buzzers
(Controls the buzzer sounding according to the CAN signals and direct line input signals.) |
1.
Combination meter assembly 2.
Main body ECU (multiplex network body ECU) |
- | ·
The status of the signals for the following buzzers is maintained: -
Seat belt warning buzzer -
Driving with any door opened warning buzzer -
PKB-ON driving warning buzzer -
Light reminder buzzer -
Key reminder buzzer -
Sliding roof open warning buzzer |
- |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
- | ·
The following buzzers do not sound: -
Seat belt warning buzzer -
Driving with any door opened warning buzzer -
PKB-ON driving warning buzzer -
Speed limit exceeded buzzer |
- | |
1.
Combination meter assembly 2.
Airbag sensor assembly |
- | The seat belt warning buzzer does not sound. | - | |
1.
Combination meter assembly 2.
4 wheel drive control ECU |
- | The 4WD buzzer does not sound. | - | |
| Drive Monitor
(Performs calculations and displays drive monitor information according to the fuel injection volume and pulse count of the vehicle pulse signal.) |
1.
Combination meter assembly 2.
ECM, Brake actuator assembly (skid control ECU), Main body ECU (multiplex network body ECU) |
The drive monitor calculations stop and the display is blank. | Nothing | - |
| Multi-display Control
(Controls the multi-display based on CAN and direct line signals.) |
1.
Combination meter assembly 2.
Brake actuator assembly (skid control ECU) |
- | ·
The status of the CRAWL control display is maintained. ·
The status of the TRC OFF display is maintained. ·
The status of the PKB-ON while driving display is maintained. |
- |
1.
Combination meter assembly 2.
Main body ECU (multiplex network body ECU) |
- | ·
The security display is turned off. ·
The status of the sliding roof warning signal is maintained. ·
The door open indicator: -
When steering wheel information is not determined: Turned off. -
When steering wheel information is determined: Status of the display is maintained. ·
When steering wheel information is determined: Status of the display is maintained. |
- | |
| Alarm
(Sounds warnings.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM |
- | Nothing | U0100 |
| Illumination Control
(Controls the daytime running lights.) |
1.
Main body ECU (multiplex network body ECU) 2.
ECM |
Control is not performed. | Nothing | U0100 |
| Display Automatic Dimming
(Controls display dimming control.) |
1.
Main body ECU (multiplex network body ECU) 2.
Combination meter assembly |
·
When communication is lost with the ignition switch off: The display does not dim. ·
When communication is lost with the ignition switch ON: The status of the display is maintained. |
Nothing | U0155 |
| Equipment Related
(Processes the ambient temperature data and transmits the data to the remote start [equipment] of the BERKES equipment as a back-up.) |
1.
Main body ECU (multiplex network body ECU) 2.
Air conditioning amplifier assembly |
- | Nothing | U0164 |
| Engine-related Indicators
(The system estimates the oil deterioration level and the indicators on the meter indicate that an oil change is necessary, etc.) |
1.
ECM 2.
Combination meter assembly |
·
The indicator lights do not turn on. ·
The meter display cannot cleared. |
The engine-related indicator lights do not turn on. | - |
| Electrical Load Control
(Performs idle up according to the electrical load.) |
1.
ECM 2.
ECM, Main body ECU (multiplex network body ECU), Air conditioning amplifier assembly |
Idle up according to the electrical load is not performed. | The idle speed changes. | - |
| Air Conditioning-linked Control
(Performs idle up according to the compressor load.) |
1.
ECM 2.
Air conditioning amplifier assembly |
Air conditioning-linked control does not operate. | The air conditioning does not operate. | - |
| TC DTC Output Service
(Outputs a DTC in response to a DTC output request from MET.) |
1.
Combination meter assembly 2.
ECM, Airbag sensor assembly |
The TC service function stops. | Nothing | - |
| Event Data Recorder (EDR)
(Records conditions such as the vehicle speed, the amount the accelerator pedal is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
1.
Airbag sensor assembly 2.
ECM, Combination meter assembly |
- | Nothing | - |
| SRS Warning Light Control
(Turns the warning light on/off.) |
1.
Combination meter assembly 2.
Airbag sensor assembly |
The SRS warning light turns on. | The SRS warning light turns on. | - |
| Collision Detection Signal (for Fuel-cut)
(Notifies the system of a collision in order to perform fuel-cut when a vehicle collision occurs.) |
1.
ECM 2.
Airbag sensor assembly |
The fuel-cut function used when a collision occurs is stopped. | Nothing | - |
| Seat Belt Warning Light Control
(Turns the seat belt warning light on/off.) |
1.
Combination meter assembly, Main body ECU (multiplex network body ECU) 2.
Airbag sensor assembly |
The seat belt warning light does not operate. | Nothing | - |