Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"Engine (ECM)" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

ECM CAN main wire or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C382927E01
5.917,1.802 6.531,2 0.615,0.198 10 false BATT 5.469,0.49 6.083,0.688 0.615,0.198 10 false G183 5.469,0.865 6.083,1.063 0.615,0.198 10 false G183 5.458,1.792 6.073,1.99 0.615,0.198 10 false G183 5.458,2.25 6.073,2.448 0.615,0.198 10 false G183 5.458,2.719 6.073,2.917 0.615,0.198 10 false G183 5.458,3.115 6.073,3.313 0.615,0.198 10 false G183 5.469,3.469 6.083,3.667 0.615,0.198 10 false C161 5.958,0.365 6.573,0.563 0.615,0.198 10 false CANH 5.958,1.052 6.573,1.25 0.615,0.198 10 false CANL 1.896,1.792 2.781,2.063 0.885,0.271 10 false from Battery 5.906,2.25 6.521,2.448 0.615,0.198 10 false +B 5.906,2.74 6.521,2.938 0.615,0.198 10 false MREL 5.917,3.115 6.531,3.313 0.615,0.198 10 false EC 5.917,3.5 6.531,3.698 0.615,0.198 10 false E1 5.938,3.833 6.552,4.031 0.615,0.198 10 false E02 5.906,4.177 6.521,4.375 0.615,0.198 10 false E01 5.531,0.302 6.146,0.5 0.615,0.198 10 false 25 5.563,0.677 6.177,0.875 0.615,0.198 10 false 31 5.583,1.615 6.198,1.813 0.615,0.198 10 false 2 5.594,2.073 6.208,2.271 0.615,0.198 10 false 1 5.469,3.833 6.083,4.031 0.615,0.198 10 false C161 5.469,4.188 6.083,4.385 0.615,0.198 10 false C161 1.646,0.271 2.26,0.469 0.615,0.198 10 false 10*1 5.542,2.531 6.156,2.729 0.615,0.198 10 false 10 5.573,2.938 6.188,3.135 0.615,0.198 10 false 7 5.563,3.302 6.177,3.5 0.615,0.198 10 false 5 5.573,3.656 6.188,3.854 0.615,0.198 10 false 6 5.573,4 6.188,4.198 0.615,0.198 10 false 7 1.771,2.208 2.844,2.469 1.073,0.26 10 false from EFI Relay 1.917,2.698 2.99,2.958 1.073,0.26 10 false to EFI Relay 1.667,0.698 2.281,0.896 0.615,0.198 10 false 21*1 0.5,1.406 2.604,1.604 2.104,0.198 10 false No. 3 CAN Junction Connector*2 0.5,1.208 2.604,1.406 2.104,0.198 10 false No. 1 CAN Junction Connector*1 0.281,4.604 2.385,4.802 2.104,0.198 10 false *1: for LHD 0.281,4.896 2.385,5.094 2.104,0.198 10 false *2: for RHD 3.635,1.917 4.25,2.115 0.615,0.198 10 false EFI 2.042,0.479 2.656,0.677 0.615,0.198 10 false G297 2.031,0.875 2.646,1.073 0.615,0.198 10 false G297 1.635,0.469 2.25,0.667 0.615,0.198 10 false A119 1.625,0.885 2.24,1.083 0.615,0.198 10 false A119 2.083,0.292 2.698,0.49 0.615,0.198 10 false 2*2 2.063,0.688 2.677,0.885 0.615,0.198 10 false 13*2 6.042,4.74 6.656,4.938 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C382920C01
1.5,0.583 1.917,0.833 0.417,0.25 2.469,2.083 2.75,0.656 2.75,0.656 2.917,0.656 true 2.5,2.417 2.615,2.823 2.615,2.823 2.781,2.823 true 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.958,0.583 3.427,0.802 0.469,0.219 10 false CANH 2.875,2.771 3.344,2.99 0.469,0.219 10 false CANL 1.542,0.625 2.01,0.844 0.469,0.219 10 false G183
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G183-25 (CANH) - G183-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the ECM connector.

C382921C01
1.667,0.417 2.083,0.667 0.417,0.25 4.885,0.417 5.302,0.667 0.417,0.25 2.5,1.177 2.667,0.5 2.667,0.5 2.833,0.5 true 5.667,1.167 5.833,0.667 5.833,0.667 6,0.667 true 5.5,1.167 5.75,0.458 5.75,0.458 5.917,0.458 true 5.333,1.167 5.646,0.25 5.646,0.25 5.813,0.25 true 0.833,0.833 1,0.833 1,0.833 1.25,1.167 true 1,0.5 1.167,0.5 1.167,0.5 1.5,1.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.719,0.458 2.177,0.688 0.458,0.229 10 false G183 4.938,0.458 5.396,0.688 0.458,0.229 10 false C161 2.885,0.427 3.344,0.656 0.458,0.229 10 false EC 6.094,0.604 6.552,0.833 0.458,0.229 10 false E01 5.979,0.396 6.438,0.625 0.458,0.229 10 false E02 5.885,0.177 6.344,0.406 0.458,0.229 10 false E1 0.583,0.771 1.042,1 0.458,0.229 10 false +B 0.604,0.427 1.063,0.656 0.458,0.229 10 false BATT
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C161-5 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C161-7 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C161-6 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G183-7 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G183-2 (BATT) - Body ground Always 11 to 14 V
G183-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G183-10 (MREL) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)