Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Airbag sensor assembly CAN branch wire or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C245775E09
0.938,1.979 3.01,2.438 2.073,0.458 10 false No. 2 CAN Junction Connector*1 5.854,0.99 6.375,1.125 0.521,0.135 10 false CANH 5.49,0.885 5.698,1.063 0.208,0.177 10 false 13 5.854,1.427 6.406,1.646 0.552,0.219 10 false CANL 5.5,1.313 5.698,1.521 0.198,0.208 10 false 22 5.844,2.594 6.375,2.813 0.531,0.219 10 false IG2 5.521,2.479 5.75,2.667 0.229,0.188 10 false 21 5.854,3.385 6.375,3.615 0.521,0.229 10 false E1 5.521,3.281 5.75,3.5 0.229,0.219 10 false 25 5.854,4.042 6.417,4.302 0.563,0.26 10 false E2 5.521,3.927 5.719,4.146 0.198,0.219 10 false 26 4.354,2.438 5.198,2.698 0.844,0.26 10 false IGN 1.698,2.583 2.781,3.042 1.083,0.458 10 false from IG2 Relay 5.521,4.958 7.073,5.333 1.552,0.375 10 false Airbag Sensor Assembly 0.969,1.823 2.188,2.031 1.219,0.208 10 false G293*1, G295*2 1.958,0.865 2.177,1.104 0.219,0.24 10 false 5 1.958,1.323 2.177,1.5 0.219,0.177 10 false 16 5.521,4.771 6.042,4.917 0.521,0.146 10 false G1 0.948,2.188 3.021,2.646 2.073,0.458 10 false No. 4 CAN Junction Connector*2 0.563,4.573 1.646,5.031 1.083,0.458 10 false *1: for LHD 0.573,4.896 1.656,5.354 1.083,0.458 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.
C210016C25
0.302,1 0.75,1.302 0.448,0.302 1.99,1.052 2.198,0.448 2.198,0.448 2.333,0.448 true 2.094,1.323 2.271,1.698 2.271,1.698 2.417,1.698 true 0.052,0.063 0.24,0.24 0.188,0.177 10 false *a 2.375,0.375 2.813,0.552 0.438,0.177 10 false CANH 0.406,1.073 0.688,1.25 0.281,0.177 10 false G1 2.458,1.615 2.896,1.792 0.438,0.177 10 false CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPLACE CAN BUS BRANCH WIRE AND CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C210016C26
0.323,1.021 0.792,1.323 0.469,0.302 2.198,1.25 2.406,0.917 2.406,0.917 2.542,0.917 true 1.792,1.313 1.969,1.688 1.969,1.688 2.115,1.688 true 1.646,1.313 1.302,1.719 1.302,1.719 1.125,1.719 true 0.052,0.052 0.24,0.229 0.188,0.177 10 false *a 2.583,0.844 3.021,1.021 0.438,0.177 10 false IG2 0.448,1.104 0.719,1.281 0.271,0.177 10 false G1 2.146,1.625 2.583,1.802 0.438,0.177 10 false E1 0.927,1.625 1.365,1.802 0.438,0.177 10 false E2
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-25 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G1-26 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

NG

REPLACE HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)