Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VSC OFF SWITCH(w/o Combination Switch) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0328345 VSC OFF SWITCH(w/o Combination Switch) G

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VSC OFF SWITCH(w/o Combination Switch)  INSPECTION  


PROCEDURE

Hide 84970E 1.INSTALL NO. 2 COMBINATION SWITCH ASSEMBLY

a.
C380114C05
0.792,1.75 0.792,1.313 true 2.635,0.365 2.469,0.365 2.469,0.365 2.469,1.031 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 0.75,1.802 1.094,2 0.344,0.198 10 false E 2.688,0.281 3.104,0.49 0.417,0.208 10 false OFF
*a Component without harness connected
(No. 2 Combination Switch Assembly (VSC OFF switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (OFF) - 24 (E) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the No. 2 combination switch assembly (VSC OFF switch).


b.
C380114C04
2.646,1.781 2.646,1.344 true 0.948,0.26 0.781,0.26 0.781,0.26 0.781,1.01 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.021,0.167 1.365,0.365 0.344,0.198 10 false ILL-
*a Component without harness connected
(No. 2 Combination Switch Assembly (VSC OFF switch))


Apply battery voltage between the terminals of the No. 2 combination switch assembly (VSC OFF switch), and check the illumination condition of the No. 2 combination switch assembly (VSC OFF switch).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the No. 2 combination switch assembly (VSC OFF switch).


Hide 84988L 2.INSPECT VSC OFF SWITCH

a.
C375581C01
1.167,1.885 1.333,1.885 1.333,1.885 1.333,1.302 true 2.177,1.885 2.01,1.885 2.01,1.885 2.01,1.302 true 1,1.802 1.208,2.021 0.208,0.219 10 false B 2.219,1.813 2.438,2.021 0.219,0.208 10 false E 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(VSC OFF switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (OFF) - 2 (E) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the VSC OFF switch.


b.
C375581C02
0.948,1.885 1.115,1.885 1.115,1.885 1.115,1.302 true 2.427,1.885 2.26,1.885 2.26,1.885 2.26,1.302 true 0.615,1.781 1.031,2.01 0.417,0.229 10 false +ILL 2.469,1.781 2.885,1.99 0.417,0.208 10 false -ILL 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(VSC OFF switch)


Apply battery voltage between the terminals of the VSC OFF switch, and check the illumination condition of the VSC OFF switch.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the VSC OFF switch.