The ECM illuminates the cruise control SET indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control SET indicator illuminates when the cruise control system is controlling vehicle speed. The cruise SET indicator light circuit uses CAN communication. If the cruise control SET indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.
Observe the following items for safety reasons when using the GTS:
Before using the GTS, read the instruction manual.
Prevent the GTS cable from being caught on the pedals, shift lever or steering wheel when driving with the GTS connected to the vehicle.
When driving the vehicle for testing purposes, 2 people are required. One person should operate the GTS while the other drives the vehicle.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before replacing the ECM refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
w/ Multi-information Display:
Perform the Active Test according to the display on the GTS.
Body Electrical > Combination Meter > Active Test
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display 1 | Multi-information display | OFF or All | - |
The multi-information display in the combination meter assembly turns off or completely on according to the GTS operation
w/o Multi-information Display:
Perform the Active Test according to the display on the GTS.
Body Electrical > Combination Meter > Active Test
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. SET | Cruise control SET indicator light | OFF or ON | - |
Cruise control SET indicator light turns ON/OFF
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the cruise control system on using the cruise control main switch (ON-OFF button).
Drive at a speed between approximately 40 km/h (25 mph) and 200 km/h (125 mph).
Enter the following menus: Powertrain / Cruise Control / Data List.
for 1GR-FE (for Manual Transmission):
Read the Data List according to the display on the GTS.
Powertrain > Cruise Control > Data List
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SET/COAST Switch | -SET switch signal | ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
except 1GR-FE (for Manual Transmission):
Read the Data List according to the display on the GTS.
Powertrain > Cruise Control > Data List
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| -SET Switch | -SET switch signal | ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| Result | Proceed to |
|---|---|
| The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-SET switch). | A |
| The cruise control SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the cruise control main switch (-SET switch). | B |
| The cruise control SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the cruise control main switch (-SET switch). | C |
A
B
C
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL