Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › CRAWL SWITCH › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260919 CRAWL SWITCH G

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  CRAWL SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY (CRAWL SWITCH)

a.
C375584C01
1.083,2.021 1.083,1.188 1.083,1.188 0.917,1.188 true 1.354,1.75 1.354,0.667 1.354,0.667 1.188,0.667 true 1.74,1.656 1.74,0.24 1.74,0.24 1.573,0.24 true 2.115,1.729 2.115,0.646 2.115,0.646 2.281,0.646 true 2.396,1.99 2.396,1.24 2.396,1.24 2.563,1.24 true 0.74,1.104 1.052,1.26 0.313,0.156 10 false *a 1.021,0.583 1.333,0.74 0.313,0.156 10 false *b 1.417,0.156 1.729,0.313 0.313,0.156 10 false *c 2.323,0.563 2.635,0.719 0.313,0.156 10 false *d 2.615,1.167 2.927,1.323 0.313,0.156 10 false *e
*a LO
*b LO / MEDIUM
*c MEDIUM
*d MEDIUM / HI
*e HI


C281308C17
1.26,1.25 1.063,1.625 1.063,1.625 1.063,1.76 true 1.615,1.25 1.573,1.635 1.573,1.635 1.573,1.76 true 1.802,1.25 2.052,1.667 2.052,1.667 2.052,1.792 true 2,1.26 2.531,1.667 2.531,1.667 2.531,1.771 true 0.74,1.24 0.604,1.656 0.604,1.656 0.604,1.771 true 0.104,0.042 0.302,0.24 0.198,0.198 10 false *a 0.563,1.792 0.74,1.958 0.177,0.167 10 false E 0.938,1.792 1.292,1.958 0.354,0.167 10 false FRB 1.469,1.792 1.823,1.958 0.354,0.167 10 false DN 1.969,1.802 2.323,1.969 0.354,0.167 10 false UP 2.406,1.792 2.76,1.958 0.354,0.167 10 false ECU
*a Component without harness connected
Combination Switch Assembly (Crawl Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
17 (ECU) - 24 (E) LO Below 1 Ω
18 (UP) - 24 (E)
19 (DN) - 24 (E) 10 kΩ or higher
17 (ECU) - 24 (E) LO / MEDIUM Below 1 Ω
18 (UP) - 24 (E) 10 kΩ or higher
19 (DN) - 24 (E)
17 (ECU) - 24 (E) MEDIUM 10 kΩ or higher
18 (UP) - 24 (E)
19 (DN) - 24 (E)
17 (ECU) - 24 (E) MEDIUM / HI 10 kΩ or higher
18 (UP) - 24 (E)
19 (DN) - 24 (E) Below 1 Ω
17 (ECU) - 24 (E) HI 10 kΩ or higher
18 (UP) - 24 (E) Below 1 Ω
19 (DN) - 24 (E)
21 (FRB) - 24 (E) ON/OFF: Pressed Below 1 Ω
ON/OFF: Not pressed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly (crawl switch).


b.
C281308C16
0.74,0.958 0.74,0.281 0.74,0.281 0.906,0.281 true 2.563,1.74 2.729,1.74 2.729,1.74 2.729,1.24 true 2.26,1.646 2.563,1.865 0.302,0.219 10 false ILL+ 0.969,0.177 1.344,0.406 0.375,0.229 10 false ILL- 0.073,0.021 0.417,0.24 0.344,0.219 10 false *a
*a Component without harness connected
Combination Switch Assembly (Crawl Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly (crawl switch).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly (crawl switch).