Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › MULTI-TERRAIN SELECT SWITCH › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260922 MULTI-TERRAIN SELECT SWITCH G

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  MULTI-TERRAIN SELECT SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY (MULTI-TERRAIN SELECT SWITCH)

a.
C375584C01
1.083,2.021 1.083,1.188 1.083,1.188 0.917,1.188 true 1.354,1.75 1.354,0.667 1.354,0.667 1.188,0.667 true 1.74,1.656 1.74,0.24 1.74,0.24 1.573,0.24 true 2.115,1.729 2.115,0.646 2.115,0.646 2.281,0.646 true 2.396,1.99 2.396,1.24 2.396,1.24 2.563,1.24 true 0.74,1.104 1.052,1.26 0.313,0.156 10 false *a 1.021,0.583 1.333,0.74 0.313,0.156 10 false *b 1.417,0.156 1.729,0.313 0.313,0.156 10 false *c 2.323,0.563 2.635,0.719 0.313,0.156 10 false *d 2.615,1.167 2.927,1.323 0.313,0.156 10 false *e
*a MUD & SAND
*b LOOSE ROCK
*c MOGUL
*d ROCK & DIRT
*e ROCK


C281308C17
1.26,1.25 1.063,1.625 1.063,1.625 1.063,1.76 true 1.615,1.25 1.573,1.635 1.573,1.635 1.573,1.76 true 1.802,1.25 2.052,1.667 2.052,1.667 2.052,1.792 true 2,1.26 2.531,1.667 2.531,1.667 2.531,1.771 true 0.74,1.24 0.604,1.656 0.604,1.656 0.604,1.771 true 0.104,0.042 0.302,0.24 0.198,0.198 10 false *a 0.563,1.792 0.74,1.958 0.177,0.167 10 false E 0.938,1.792 1.292,1.958 0.354,0.167 10 false FRB 1.469,1.792 1.823,1.958 0.354,0.167 10 false DN 1.969,1.802 2.323,1.969 0.354,0.167 10 false UP 2.406,1.792 2.76,1.958 0.354,0.167 10 false ECU
*a Component without harness connected
Combination Switch Assembly (Multi-Terrain Select Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
17 (ECU) - 24 (E) MUD & SAND Below 1 Ω
18 (UP) - 24 (E)
19 (DN) - 24 (E) 10 kΩ or higher
17 (ECU) - 24 (E) LOOSE ROCK Below 1 Ω
18 (UP) - 24 (E) 10 kΩ or higher
19 (DN) - 24 (E)
17 (ECU) - 24 (E) MOGUL 10 kΩ or higher
18 (UP) - 24 (E)
19 (DN) - 24 (E)
17 (ECU) - 24 (E) ROCK & DIRT 10 kΩ or higher
18 (UP) - 24 (E)
19 (DN) - 24 (E) Below 1 Ω
17 (ECU) - 24 (E) ROCK 10 kΩ or higher
18 (UP) - 24 (E) Below 1 Ω
19 (DN) - 24 (E)
20 (FRE) - 24 (E) ON/OFF: Pressed Below 1 Ω
ON/OFF: Not pressed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly (multi-terrain select switch).


b.
C281308C16
0.74,0.958 0.74,0.281 0.74,0.281 0.906,0.281 true 2.563,1.74 2.729,1.74 2.729,1.74 2.729,1.24 true 2.26,1.646 2.563,1.865 0.302,0.219 10 false ILL+ 0.969,0.177 1.344,0.406 0.375,0.229 10 false ILL- 0.073,0.021 0.417,0.24 0.344,0.219 10 false *a
*a Component without harness connected
Combination Switch Assembly (Multi-Terrain Select Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly (multi-terrain select switch).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly (multi-terrain select switch).