Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM J

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the parking assist ECU.

WIRING DIAGRAM

E301406E29
5.271,2.938 6.781,3.26 1.51,0.323 10 false Parking Assist ECU 5.271,2.75 5.729,2.948 0.458,0.198 10 false I6 5.333,2.156 6.01,2.375 0.677,0.219 10 false GND1 5.333,1.74 6.01,1.958 0.677,0.219 10 false ACC 5.333,1.344 6.01,1.563 0.677,0.219 10 false IG 5.323,0.896 6,1.115 0.677,0.219 10 false +B 5.104,0.813 5.26,1.01 0.156,0.198 10 false 1 5.115,1.24 5.271,1.438 0.156,0.198 10 false 8 5.125,1.656 5.281,1.854 0.156,0.198 10 false 9 5.125,2.052 5.292,2.271 0.167,0.219 10 false 4 3.396,1.063 4.344,1.323 0.948,0.26 10 false ECU-B 3.24,1.479 4.354,1.719 1.115,0.24 10 false ECC-IG NO.2 3.479,1.896 4.271,2.125 0.792,0.229 10 false ACC 1.396,0.885 2.385,1.125 0.99,0.24 10 false from Battery 0.948,1.302 2.292,1.521 1.344,0.219 10 false from IG NO.1 Relay 1.177,1.74 2.292,1.99 1.115,0.25 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION)

*1: for Navigation Receiver Type

*2: for Radio and Display Type


·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U165548E03
1.99,1.281 2.198,1.49 2.198,1.49 2.469,1.49 true 2.24,1.781 2.063,1.781 2.063,1.781 1.927,1.292 true 1.271,1.115 1.063,0.906 1.063,0.906 0.792,0.906 true 2.24,1.104 2.438,0.896 2.438,0.896 2.708,0.896 true 0.146,0.135 0.552,0.458 0.406,0.323 10 false *a 1.708,0.26 2.052,0.458 0.344,0.198 10 false I6 2.292,1.698 2.802,1.885 0.51,0.188 10 false ACC 0.313,0.823 0.792,1.125 0.479,0.302 10 false GND1 2.771,0.802 3.208,1.063 0.438,0.26 10 false +B 2.521,1.427 2.979,1.667 0.458,0.24 10 false IG

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-1 (+B) - Body ground Always 11 to 14 V
I6-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
I6-9 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V



Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR