Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal* Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.
Steering Unlock Switch State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) OFF or ON OFF: Steering locked
ON: Steering unlocked
·

When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Start Switch1 Engine switch 1 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Neutral SW/ Clutch SW
for Automatic Transmission

Shift position (P and N)


for Manual Transmission

State of clutch pedal


ON or OFF
for Automatic Transmission

ON: Shift lever in P or N

OFF: Shift lever in any position other than P or N


for Manual Transmission

ON: Clutch pedal depressed

OFF: Clutch pedal released


for Automatic Transmission
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, OFF is displayed.


for Manual Transmission
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Latch Circuit Status of IG related backup circuits OFF or ON OFF: Engine switch off
ON: Engine switch on (IG)
·

Displays in almost the same manner as the IG relay.

·

When the engine switch is on (ACC), OFF is displayed.


Starter Request Signal Engine start request signal status OFF or ON OFF: After approximately 1 second has elapsed, the engine switch is released
ON: With the shift lever in P* and brake pedal depressed, the engine switch is pressed and held
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


ACC Relay Monitor ACC relay activation OFF or ON OFF: Engine switch off
ON: Engine switch on (ACC)
When the engine switch is on (IG), ON is displayed.
Engine Condition Engine state Stop or Run Stop: Engine stopped
Run: Engine running
-
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Powertrain Type Vehicle identification HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT, S&S-MMT or PHV-AT Cnv-AT: Conventional automatic transmission models
Cnv-MT: Conventional manual transmission models
-
Starter SW Sig Mismatch Engine switch signal 1 and 2 do not match No or Yes No: Switch normal
Yes: Switch malfunctioning (Engine switch signal 1 and 2 do not match)
Even when Yes is displayed, the engine can be started. However, engine emergency stop while driving by pressing and holding the engine switch cannot be performed, and if the brakes are malfunctioning, engine emergency start by pressing and holding the engine switch cannot be performed.
Park Signal Mismatch* P position signal malfunction No or Yes No: Signal normal
Yes: Signal malfunction (CAN communication and direct line signal do not match)
Even when Yes is displayed, it is still possible to turn the engine switch off (the power source mode will not be stuck in on (ACC) or on (IG)).
Str Lock/Unlock Wait T-Out Steering lock or unlock malfunction No or Yes No: Lock and unlock normal
Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.)
When the engine cannot be started due to a steering lock or unlock malfunction, Yes is displayed.
Key Certif Wait T-Out Key verification malfunction No or Yes No: Verification normal
Yes: Verification error (Detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching)
When the engine cannot be started due to a key verification error, Yes is displayed.
IG Circuit IG relay coil circuit malfunction OK or NG OK: Circuit normal
NG: Circuit malfunctioning
·

Use this item to determine whether the IG relay is malfunctioning.

·

When the engine cannot be started due to an IG relay malfunction, NG is displayed.


IG Relay Monitor (Outside) IG relay coil voltage monitor status OFF or ON OFF: Engine switch off
ON: Engine switch on (IG)
·

Use this item to determine whether the IG relay is malfunctioning.

·

When the engine switch is on (ACC), OFF is displayed.


IG Relay Monitor (Inside) IG relay activation OFF or ON OFF: Engine switch off
ON: Engine switch on (IG)
·

Use this item to determine whether the IG relay is malfunctioning.

·

When the engine switch is on (ACC), OFF is displayed.


Number of Diagnosis Code Number of DTCs 0 to 255 0 -

*: for Automatic Transmission


Data List Display Changes when the Engine is Started (for Automatic Transmission):
C278722E14
2.917,0.167 3.229,0.365 0.313,0.198 10 false *1 3.563,0.167 3.875,0.365 0.313,0.198 10 false *2 4,0.167 4.313,0.365 0.313,0.198 10 false *3 4.354,0.177 4.667,0.375 0.313,0.198 10 false *4 5.281,0.188 5.594,0.385 0.313,0.198 10 false *5 5.583,0.188 5.896,0.385 0.313,0.198 10 false *6 6.365,0.188 6.677,0.385 0.313,0.198 10 false *7 0.094,0.635 2.083,0.833 1.99,0.198 10 false Start Switch1 0.094,1.49 2.083,1.688 1.99,0.198 10 false Steering Unlock Switch 0.104,2.302 1.479,2.5 1.375,0.198 10 false Stop Light Switch1 0.094,3.031 2.24,3.25 2.146,0.219 10 false Neutral SW/ Clutch SW 0.083,3.75 2.198,4.125 2.115,0.375 10 false IG Relay Monitor (Outside) 0.104,4.771 1.604,5.146 1.5,0.375 10 false ACC Relay Monitor 0.094,5.708 1.813,6.208 1.719,0.5 10 false Starter Request Signal 0.083,6.656 1.802,7.052 1.719,0.396 10 false Engine Condition 0.125,7.302 1.688,7.719 1.563,0.417 10 false Power Supply Condition 2.354,0.667 2.667,0.865 0.313,0.198 10 false ON 2.333,0.927 2.792,1.125 0.458,0.198 10 false OFF 2.354,1.469 2.667,1.667 0.313,0.198 10 false ON 2.333,1.75 2.792,1.948 0.458,0.198 10 false OFF 2.354,2.292 2.667,2.49 0.313,0.198 10 false ON 2.333,2.563 2.792,2.76 0.458,0.198 10 false OFF 2.354,3.167 2.667,3.365 0.313,0.198 10 false ON 2.354,3.813 2.667,4.01 0.313,0.198 10 false ON 2.333,3.427 2.792,3.625 0.458,0.198 10 false OFF 2.302,4.021 2.76,4.219 0.458,0.198 10 false OFF 2.354,4.802 2.667,5 0.313,0.198 10 false ON 2.333,5 2.792,5.198 0.458,0.198 10 false OFF 2.354,5.74 2.667,5.938 0.313,0.198 10 false ON 2.333,5.938 2.792,6.135 0.458,0.198 10 false OFF 2.333,6.667 2.792,6.865 0.458,0.198 10 false Run 2.302,6.969 2.802,7.25 0.5,0.281 10 false Stop 2.031,7.333 2.542,7.552 0.51,0.219 10 false ST ON 2.042,7.729 2.813,7.927 0.771,0.198 10 false IG ON 2.031,8.083 2.948,8.281 0.917,0.198 10 false ACC ON 2.042,8.385 2.656,8.583 0.615,0.198 10 false All OFF 0.094,0.948 2.083,1.146 1.99,0.198 10 false Start Switch2

HINT:
To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.

*1: Press the engine switch with the brake pedal released and check that the engine switch is turned on (ACC).

*2: Press the engine switch with the brake pedal released and check that the engine switch is turned on (IG).

*3: Depress the brake pedal (stop light switch is on).

*4: Press the engine switch with the brake pedal depressed and check that the engine starts.

*5: Press the engine switch with the brake pedal depressed and check that the engine switch is turned off.

*6: Release the brake pedal.

*7: Open a door.


Data List Display Changes when the Engine is Started (for Manual Transmission):
C325649E03
2.969,0.438 3.281,0.635 0.313,0.198 10 false *1 3.625,0.427 3.938,0.625 0.313,0.198 10 false *2 4.042,0.438 4.354,0.635 0.313,0.198 10 false *3 4.385,0.427 4.698,0.625 0.313,0.198 10 false *4 5.313,0.448 5.625,0.646 0.313,0.198 10 false *5 5.615,0.448 5.927,0.646 0.313,0.198 10 false *6 6.375,0.458 6.688,0.656 0.313,0.198 10 false *7 0.198,0.688 2.188,0.885 1.99,0.198 10 false Start Switch1 2.448,0.74 2.76,0.938 0.313,0.198 10 false ON 2.406,1.01 2.865,1.208 0.458,0.198 10 false OFF 2.479,1.615 2.792,1.813 0.313,0.198 10 false ON 2.458,2.469 2.771,2.667 0.313,0.198 10 false ON 2.448,3.427 2.76,3.625 0.313,0.198 10 false ON 2.448,4.531 2.76,4.729 0.313,0.198 10 false ON 2.427,5.448 2.74,5.646 0.313,0.198 10 false ON 2.365,6.365 2.823,6.563 0.458,0.198 10 false Run 2.333,6.615 2.948,6.813 0.615,0.198 10 false Stop 2.438,1.875 2.896,2.073 0.458,0.198 10 false OFF 2.417,2.708 2.875,2.906 0.458,0.198 10 false OFF 2.396,3.646 2.854,3.844 0.458,0.198 10 false OFF 2.406,4.76 2.865,4.958 0.458,0.198 10 false OFF 2.396,5.76 2.854,5.958 0.458,0.198 10 false OFF 2.104,8.156 3.177,8.354 1.073,0.198 10 false ALL OFF 2.115,7.896 3.031,8.094 0.917,0.198 10 false ACC ON 2.25,7.542 3.021,7.74 0.771,0.198 10 false IG ON 2.24,7.135 3.01,7.333 0.771,0.198 10 false ST ON 0.094,7.146 1.656,7.375 1.563,0.229 10 false Power Supply Condition 0.146,6.333 1.292,6.542 1.146,0.208 10 false Engine Condition 0.177,5.406 1.667,5.625 1.49,0.219 10 false Starter Request Signal 0.177,4.49 1.375,4.698 1.198,0.208 10 false ACC Relay Monitor 0.167,3.396 1.948,3.594 1.781,0.198 10 false IG1 Relay Monitor (Outside) 0.167,2.5 1.729,2.719 1.563,0.219 10 false Neutral SW/ Clutch SW 0.188,1.594 1.667,1.823 1.479,0.229 10 false Steering Unlock Switch 0.188,0.99 2.177,1.188 1.99,0.198 10 false Start Switch2

HINT:
To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off.

*1: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (ACC).

*2: Without depressing the clutch pedal, press the engine switch and check that the power source mode turns on (IG).

*3: Depress the clutch pedal (the clutch start switch is on).

*4: With the clutch pedal depressed, press the engine switch and check that the engine starts.

*5: Press the engine switch and check that the power source mode turns off.

*6: Release the clutch pedal.

*7: Open a door.



f.

Enter the following menus: Body Electrical / Entry&Start / Data List.


g.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
"Yes" can be displayed only when the Data List item "No Response" is "No".
# Codes Number of DTCs 0 to 255 0 -
Immobiliser Immobiliser system status determined by certification ECU (smart key ECU assembly) Set or Unset Set: Immobiliser set (engine start prohibited) (engine switch off)
Unset: Immobiliser unset (engine start permitted) (engine switch on (ACC) or on (IG))
The engine cannot be started when Set is displayed.
HINT:
·

The theft warning indicator light assembly (security indicator light) blinks when Set is displayed.

·

The theft warning indicator light assembly (security indicator light) is linked with set/unset of the immobiliser and not linked with lock/unlock of the steering.



Steering Lock Sleep Cond Steering lock ECU sleep availability No or Yes No: Sleep not available
Yes: Sleep available
-
Steering Lock Start Cond Steering lock ECU wake up signal status No or Yes No: Wake up signal not sent
Yes: Wake up signal sent
-
Engine Start Condition Status of engine start permission signal determined by steering lock ECU (steering lock actuator or upper bracket assembly) and sent to certification ECU (smart key ECU assembly) NG or OK NG: Engine start prohibited
OK: Engine start permitted
·

When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator or upper bracket assembly) and makes engine starting possible.

·

The engine cannot be started when NG is displayed.


Sensor Value History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2781 is stored) OK or NG(Past) OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.
NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.)
When NG(Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning.
Power Supply Short History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2782 is stored) OK or NG(Past) OK: History of motor power source short does not exist
NG(Past): History of motor power source short exists
This item displays history of a malfunction in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator or upper bracket assembly).
Motor Driver Short History of malfunction (short) in steering lock ECU (steering lock actuator or upper bracket assembly) motor circuit (DTC B2781 is stored) OK or NG(Past) OK: History of short in the motor circuit does not exist
NG(Past): History of short in the motor circuit exists
This item displays history of a malfunction in the steering lock motor circuit in the steering lock ECU (steering lock actuator or upper bracket assembly).
Lock/Unlock Receive History of receiving an unlock request signal No or Yes No: History of receiving an unlock request signal does not exist
Yes: History of receiving an unlock request signal exists
-
Lock Bar Stuck Error History of steering not being able to unlock properly when steering lock operates for a certain period of time OK or NG(Past) OK: History of steering lock being stuck does not exist
NG(Past): History of steering lock being stuck exists
-
Engine Start Request Immobiliser unset (engine start permitted) signal from certification ECU (smart key ECU assembly) to ID code box (immobiliser code ECU) received state OK or NG OK: Signal received
NG: Signal not received
·

The ID code box (immobiliser code ECU) receives the immobiliser unset (engine start permitted) signal from the certification ECU (smart key ECU assembly) and engine start permitted when OK is displayed.

·

The engine cannot be started when NG is displayed.


S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Unlock Request Receive Unlock request signal received state OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of a engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Lock Request Receive Lock request signal received state OK or NG OK: Lock request signal received for 10 seconds of any of the doors being opened with shift lever in P* and engine switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
S Code Check(Past) Verification result history between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG(Past) OK: History of abnormal verification result does not exist
NG(Past): History of abnormal verification result exists
-
L Code Check(Past) Verification result history between the ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG(Past) OK: History of abnormal verification result does not exist
NG(Past): History of abnormal verification result exists
-
Steering Lock Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status Unset or Set Unset: Lock not confirmed
Set: Lock confirmed
When Unset is displayed, the steering is not locked.
Steering Unlock Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status Unset or Set Unset: Unlock not confirmed
Set: Unlock confirmed
When Unset is displayed, the steering is not unlocked (the engine cannot be started).
Engine Start Indicator Entry warning light OFF or ON Customization status displayed -
Open in IG2 History of IG2 input of the steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG(Past) OK: History of open in IG2 exists
NG(Past): No history of open in IG2 exists
When OK is displayed, the steering lock ECU (steering lock actuator or upper bracket assembly) has an IG2 input circuit malfunction.

*: for Automatic Transmission


C278723E03
0.104,0.115 4.854,0.396 4.75,0.281 10 false Data List Display Changes when the Steering is Locked/Unlocked: 3.313,0.479 3.625,0.677 0.313,0.198 10 false *1 3.792,0.479 4.104,0.677 0.313,0.198 10 false *2 4.865,0.49 5.177,0.688 0.313,0.198 10 false *3 5.354,0.49 5.667,0.688 0.313,0.198 10 false *4 0.104,1 2.25,1.198 2.146,0.198 10 false Engine Start Condition 0.083,1.917 1.917,2.115 1.833,0.198 10 false Engine Start Request 0.083,2.75 1.771,2.948 1.688,0.198 10 false Unlock Request Receive 0.083,3.552 1.875,3.969 1.792,0.417 10 false Lock Request Receive 0.083,4.385 2.073,4.583 1.99,0.198 10 false Steering Lock 0.083,5.25 2.375,5.448 2.292,0.198 10 false Steering Unlock 2.417,1.188 2.729,1.385 0.313,0.198 10 false OK 2.417,1.5 2.729,1.698 0.313,0.198 10 false NG 2.448,2.042 2.906,2.24 0.458,0.198 10 false NG 2.448,2.375 2.76,2.573 0.313,0.198 10 false OK 2.469,2.865 2.927,3.063 0.458,0.198 10 false NG 2.448,3.177 3.115,3.365 0.667,0.188 10 false OK 2.469,3.688 2.927,3.885 0.458,0.198 10 false NG 2.469,3.969 3.083,4.167 0.615,0.198 10 false OK 2.438,4.5 2.75,4.698 0.313,0.198 10 false Set 2.302,4.74 2.76,4.938 0.458,0.198 10 false Unset 2.448,5.365 2.76,5.563 0.313,0.198 10 false Set 2.333,5.615 2.792,5.813 0.458,0.198 10 false Unset

HINT:
To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the engine switch off and the shift lever in P.(for Automatic Transmission)

*1: Press the engine switch with the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) released and check that the engine switch turns on (ACC).

*2: Press the engine switch with the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) released and check that the engine switch turns on (IG).

*3: Press the engine switch and check that the engine switch turns off.

*4: Release the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission), open the driver side door and check that the steering locks.



h.

Enter the following menus: Body Electrical / Starting Control / Data List.


i.

Read the Data List according to the display on the GTS.

Starting Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request OFF or ON OFF: Starter operation not requested
ON: Starter operation requested
When malfunctioning, the engine will not crank.
Shift Position P or N* Park/Neutral position switch status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
When malfunctioning, the engine will not crank.
Starter Relay Starter relay voltage monitor OFF or ON OFF: ST relay off
ON: ST relay on
OFF is displayed when the engine cannot crank.
Starting Control SW Starter request signal monitor OFF or ON OFF: Starting control switch off
ON: Starting control switch on
When malfunctioning, the engine will not crank.
Ignition IG2 status OFF or ON OFF: IG2 relay off
ON: IG2 relay on
-
Engine Speed Engine speed 0 to 16383 rpm Fluctuates in accordance with engine speed -
Number of DTCs Number of DTCs 0 to 255 0 -

*: for Automatic Transmission


C245088E03
2.667,1.344 2.99,1.51 0.323,0.167 10 false ON 2.667,1.615 3.063,1.781 0.396,0.167 10 false OFF 2.667,2.177 2.948,2.333 0.281,0.156 10 false ON 2.667,2.448 3.01,2.604 0.344,0.156 10 false OFF 2.667,0.583 2.917,0.75 0.25,0.167 10 false ON 2.667,0.875 3.063,1.042 0.396,0.167 10 false OFF 2.344,3.125 3.135,3.323 0.792,0.198 10 false 1000 rpm 2.333,2.927 3.167,3.115 0.833,0.188 10 false 1500 rpm 4.688,0.135 4.833,0.292 0.146,0.156 10 false * 0.396,2.927 1.896,3.198 1.5,0.271 10 false Engine Speed 0.396,2.208 1.948,2.479 1.552,0.271 10 false Starting Control SW 0.396,1.354 1.531,1.583 1.135,0.229 10 false Starter Relay 0.396,0.594 1.656,0.906 1.26,0.313 10 false Starter SW

HINT:

*: With the engine switch on (IG), the shift lever in P (for Automatic Transmission) and the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) depressed, press the engine switch and check that the engine starts.



j.

Enter the following menus: Body Electrical / Combination Meter / Data List.


k.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed (Speedometer tester) -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Control Range Diagnostic Note
P Supply for Steering Lock Certification ECU (smart key ECU assembly) OFF/ON
HINT:

OFF: Power is not supplied.

ON: Power is supplied.


When performing this Active Test, make sure the following condition is met:
The engine switch is on (IG).


f.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Control Range Diagnostic Note
Overhead Tuner Power Supply ON Door control receiver OFF/ON -
Power/Engine SW Light Engine switch light OFF/ON When performing this Active Test, make sure the following conditions are met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is started.


h.

Enter the following menus: Body Electrical / Starting Control / Active Test.


i.

Perform the Active Test according to the display on the GTS.

Starting Control
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Starter Relay ST relay OFF/ON The electrical key transmitter sub-assembly is in the cabin and the engine is stopped.