Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit and IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.*3


·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Turn the engine switch on (IG).



*1: Only detected while a malfunction is present and the engine switch is on (IG).

*2: The IG circuits activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit maintains the power source mode in on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit



WIRING DIAGRAM

B492205E01
5.365,2.146 6.896,2.615 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 3.948,0.542 4.719,0.74 0.771,0.198 10 false SMART 2,0.354 3,0.552 1,0.198 10 false from Battery 1.76,1.031 2.885,1.229 1.125,0.198 10 false to Each IG Relay 5.25,0.385 5.667,0.583 0.417,0.198 10 false G215 5.25,1.75 5.667,1.948 0.417,0.198 10 false G215 5.25,1.052 5.667,1.25 0.417,0.198 10 false G213 5.688,0.385 6,0.583 0.313,0.198 10 false +B 5.688,1.052 6.083,1.25 0.396,0.198 10 false IG1D 5.698,1.76 6.01,1.958 0.313,0.198 10 false E 5.344,1.531 5.656,1.729 0.313,0.198 10 false 11 5.333,0.167 5.646,0.365 0.313,0.198 10 false 10 5.365,0.844 5.677,1.042 0.313,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B340745C70
1.469,2.271 1.917,2.5 0.448,0.229 2.615,4.146 2.438,3.51 false 0.385,2.563 0.698,2.76 0.313,0.198 10 false *a 1.51,2.292 1.938,2.573 0.427,0.281 10 false G215 2.573,4.208 2.938,4.406 0.365,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G215-10 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B340745C71
1.417,2.271 1.833,2.5 0.417,0.229 0.813,4.083 0.917,3.635 false 0.427,2.406 0.74,2.604 0.313,0.198 10 false *a 1.448,2.292 1.854,2.51 0.406,0.219 10 false G215 0.781,4.135 1.094,4.333 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B492206C01
1.417,0.208 1.833,0.417 0.417,0.208 1.188,1.75 1.188,0.917 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.448,0.229 1.844,0.396 0.396,0.167 10 false G213 1.063,1.75 1.458,1.917 0.396,0.167 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G213-3 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)