Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B268088N23
1.479,0.26 1.917,0.5 0.438,0.24 1.521,0.292 2,0.479 0.479,0.188 10 false G206

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G206-6 (AGND) - Body ground - GR - Body ground Transponder key amplifier ground Always Below 1 Ω -
G206-7 (TXCT) - G206-6 (AGND) Input W - GR Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G206-8 (CODE) - G206-6 (AGND) Output V - GR Immobiliser communication output Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G206-10 (VC5) - G206-6 (AGND) Input P - GR Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G206-7 (TXCT) - G206-6 (AGND) Input W - GR Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



G206-8 (CODE) - G206-6 (AGND) Output V - GR Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
G206-10 (VC5) - G206-6 (AGND) Input P - GR Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G206-7 (TXCT) - G206-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B368716C10
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G206-8 (CODE) - G206-6 (AGND)
Tool Setting
·

Waveform

2 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G206-10 (VC5) - G206-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B491335C01
3.25,0.469 3.667,0.667 0.417,0.198 1.667,0.469 2.083,0.667 0.417,0.198 5,0.469 5.417,0.667 0.417,0.198 1.698,0.479 2.313,0.677 0.615,0.198 10 false G213 3.281,0.479 3.896,0.677 0.615,0.198 10 false G214 5.042,0.479 5.656,0.677 0.615,0.198 10 false G215

a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G215-10 (+B) - G215-11 (E) Input V - W-B +B power supply Always 11 to 14 V -
G215-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G215-14 (TXCT) - G215-12 (AGND) Output W - GR Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G215-13 (CODE) - G215-12 (AGND) Input V - GR Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G215-15 (VC5) - G215-12 (AGND) Output P - GR Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G215-12 (AGND) - Body ground - GR - Body ground Transponder key amplifier ground Always Below 1 Ω
G215-19 (IND) - G215-11 (E) Output G - W-B Security indicator output Engine switch off → on (IG) Pulse generation → Below 2 V -

*1: for Automatic Transmission

*2: for Manual Transmission



e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G215-14 (TXCT) - G215-12 (AGND) Output W - GR Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G215-13 (CODE) - G215-12 (AGND) Input V - GR Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
G215-15 (VC5) - G215-12 (AGND) Output P - GR Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



f.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G215-14 (TXCT) - G215-12 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B368716C10
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G215-13 (CODE) - G215-12 (AGND)
Tool Setting
·

Waveform

2 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G215-15 (VC5) - G215-12 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B302477N15
1.583,0.333 1.979,0.573 0.396,0.24 1.615,0.365 2.208,0.542 0.594,0.177 10 false G207

a.

Disconnect the G207 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G207-1 (+B) - Body ground Input V - Body ground +B power supply Always 11 to 14 V B2789
G207-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the G207 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G207-3 (EFII) - G207-5 (GND) Input SB - W-B EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Engine switch off 11 to 14 V
·

B2799

·

B279A

·

EFI Code Receive

·

Engine Start Request


G207-4 (EFIO) - G207-5 (GND) Output W - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Engine switch off Below 1 V
G207-3 (EFII) - G207-5 (GND) Input SB - W-B EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
G207-4 (EFIO) - G207-5 (GND) Output W - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)


e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G207-3 (EFII) - G207-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G207-4 (EFIO) - G207-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


B269095N15
1.542,0.135 1.979,0.375 0.438,0.24 1.625,0.177 2.104,0.406 0.479,0.229 10 false G35

a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G35-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G35-3 (IGE) - G35-1 (GND) Input W - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*1

·

Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G35-4 (SLP1) - G35-1 (GND) Output SB - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*2 11 to 14 V → Below 1.5 V Sensor Value
G35-6 (IG2) - G35-1 (GND) Input W - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
G35-7 (B) - Body ground Input G - Body ground Constant power supply Always 11 to 14 V B2788

*1: for Automatic Transmission


HINT:

*2: The steering locks when any door is opened with the shift lever in P (for Automatic Transmission) and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G35-3 (IGE) - G35-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*

·

Electrical key transmitter sub-assembly carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off



*: for Automatic Transmission





CHECK ECM (for 1GR-FE)


A225776E32
0.625,0.427 0.979,0.646 0.354,0.219 1.677,0.427 2.031,0.646 0.354,0.219 3.135,0.427 3.49,0.646 0.354,0.219 4.198,0.427 4.552,0.646 0.354,0.219 5.25,0.427 5.604,0.646 0.354,0.219 6.313,0.427 6.667,0.646 0.354,0.219 0.667,0.458 1.083,0.688 0.417,0.229 10 false G55 1.719,0.458 2.208,0.698 0.49,0.24 10 false G56 3.177,0.458 3.594,0.688 0.417,0.229 10 false C34 4.25,0.458 4.708,0.698 0.458,0.24 10 false C35 5.292,0.458 5.719,0.688 0.427,0.229 10 false C36 6.354,0.458 6.729,0.688 0.375,0.229 10 false C37

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C36-12 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G56-8 (IMO) - C36-12 (E1)*1
G56-20 (IMO) - C36-12 (E1)*2
Output SB - BR Certification ECU (smart key ECU assembly) communication output Engine switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G56-10 (IMI) - C36-12 (E1)*1
G56-14 (IMI) - C36-12 (E1)*2
Input W - BR Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G56-8 (IMO) - C36-12 (E1)*1
G56-20 (IMO) - C36-12 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

*1: for Automatic Transmission

*2: for Manual Transmission



ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G56-10 (IMI) - C36-12 (E1)*1
G56-14 (IMI) - C36-12 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal

*1: for Automatic Transmission

*2: for Manual Transmission





CHECK ECM (for 2TR-FE)


A347038C23
1,2.167 1.417,2.417 0.417,0.25 2.5,2.167 2.917,2.417 0.417,0.25 4.219,2.167 4.667,2.417 0.448,0.25 5.583,2.167 6,2.417 0.417,0.25 0.698,0.313 1.094,0.583 0.396,0.271 2,0.313 2.448,0.573 0.448,0.26 3.417,0.344 3.865,0.604 0.448,0.26 4.813,0.313 5.26,0.583 0.448,0.271 6.083,0.323 6.563,0.583 0.479,0.26 0.073,0.208 0.385,0.406 0.313,0.198 12 false *A 0.094,2.063 0.406,2.26 0.313,0.198 12 false *B 0.74,0.365 1.198,0.563 0.458,0.198 10 false C153 2.063,0.365 2.521,0.563 0.458,0.198 10 false C154 3.479,0.385 3.938,0.583 0.458,0.198 10 false C155 4.865,0.365 5.323,0.563 0.458,0.198 10 false G181 6.156,0.365 6.615,0.563 0.458,0.198 10 false G180 1.052,2.208 1.51,2.406 0.458,0.198 10 false C153 2.552,2.208 3.01,2.406 0.458,0.198 10 false C154 4.271,2.208 4.729,2.406 0.458,0.198 10 false G181 5.635,2.208 6.094,2.406 0.458,0.198 10 false G180
*A for Automatic Transmission *B for Manual Transmission


a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C153-3 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G181-9 (IMO) - C153-3 (E1) Output SB - BR Certification ECU (smart key ECU assembly) communication output Engine switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G181-10 (IMI) - C153-3 (E1) Input W - BR Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G181-9 (IMO) - C153-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G181-10 (IMI) - C153-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1KD-FTV)


U170600E03
0.719,0.844 1.01,1.021 0.292,0.177 10 false G57 1.688,0.844 1.979,1.021 0.292,0.177 10 false G58 3.208,0.844 3.5,1.021 0.292,0.177 10 false C90 4.115,0.844 4.406,1.021 0.292,0.177 10 false C91 5.021,0.844 5.313,1.021 0.292,0.177 10 false C92 6.104,0.844 6.396,1.021 0.292,0.177 10 false C93

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C93-1 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
G58-29 (IMO) - C93-1 (E1) Output SB - BR Certification ECU (smart key ECU assembly) communication output Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
G58-28 (IMI) - C93-1 (E1) Input W - BR Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G58-29 (IMO) - C93-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G58-28 (IMI) - C93-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (for 1GD-FTV)


A340466E48
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 1.802,0.479 2.208,0.667 0.406,0.188 10 false C150 0.594,0.479 1,0.677 0.406,0.198 10 false C149 2.906,0.479 3.344,0.667 0.438,0.188 10 false C151 3.948,0.479 4.385,0.698 0.438,0.219 10 false C152 5.063,0.479 5.5,0.688 0.438,0.208 10 false G184 6.219,0.479 6.646,0.708 0.427,0.229 10 false G185

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C152-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G185-17 (IMO) - C152-1 (E1) Output SB - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
G185-16 (IMI) - C152-1 (E1) Input W - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G185-17 (IMO) - C152-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G185-16 (IMI) - C152-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected