Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0329245 ROAD SIGN ASSIST SYSTEM U

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the W22 forward recognition camera connector.



E256359E96
2.146,0.76 2.5,1 0.354,0.24 2.177,0.802 2.635,1 0.458,0.198 10 false W22

a.

Disconnect the W22 forward recognition camera connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-7 (IGB) - W22-10 (GND) G - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
W22-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the W22 forward recognition camera connector.


d.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-5 (CA1P) - W22-10 (GND) GR - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
W22-11 (CA1N) - W22-10 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
W22-6 (CANH) - W22-10 (GND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
W22-12 (CANL) - W22-10 (GND) W - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

WAVEFORM 1

Item Content
Terminal Name Between W22-5 (CA1P) and W22-10 (GND)
Between W22-6 (CANH) and W22-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

WAVEFORM 2

Item Content
Terminal Name Between W22-11 (CA1N) and W22-10 (GND)
Between W22-12 (CANL) and W22-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.