Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.


f.

Check the details of the DTC(s).



CLEAR DTC (CLEAR USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Clear the DTCs.



START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

·

Start diagnostic mode using either of the 2 methods below.



a.

Method 1

i.
E376791C01
0.615,1.292 0.927,1.49 0.313,0.198 10 false *a
*a "AUDIO" Switch


Start the engine.


ii.

While pressing and holding the "AUDIO" switch of the multi-display assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


iii.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



b.

Method 2

NOTICE:

If the operation fails and diagnostic mode cannot be entered, turn the navigation receiver assembly screen display on and off once, and then perform the procedures listed below from the first step again (Only turning the navigation receiver assembly power supply on and off will not work).


i.
E376792C01
0.219,0.188 0.594,0.427 0.375,0.24 10 false *A 0.281,1.885 0.656,2.125 0.375,0.24 10 false *B 0.792,0.99 1.167,1.229 0.375,0.24 10 false *a 2.458,2.542 2.833,2.781 0.375,0.24 10 false *a 0.792,1.125 1.167,1.365 0.375,0.24 10 false *b 2.469,2.698 2.844,2.938 0.375,0.24 10 false *b
*A for RHD
*B for LHD
*a ">" Switch
*b "<" Switch


Start the engine.


ii.

Turn the navigation receiver assembly screen display off.


iii.

Turn the navigation receiver assembly power supply off.


iv.

Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.


v.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.




FAILURE DIAGNOSIS


a.
E278016

The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.



SYSTEM CHECK


a.
E287732

The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


HINT:

When "NCON" is displayed for all devices connected using the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>AVC-LAN Circuit).


a.
E287733E01
3.116,0.691 3.310,0.874 0.194,0.184 10 *e 3.155,1.374 3.361,1.558 0.206,0.184 10 *d 1.902,1.746 2.145,1.929 0.243,0.184 10 *c 0.51,1.776 0.753,1.959 0.243,0.184 10 *a 1.047,1.776 1.290,1.959 0.243,0.184 10 *b 0.651,1.122 0.651,1.707 false 1.12,1.129 1.12,1.728 false 2.01,1.541 2.01,1.746 false 2.902,1.46 3.106,1.46 false 2.885,0.794 3.089,0.794 false

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check Result Result codes for all devices are displayed.
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared.

·

Press the "Memory CLR" switch for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

The "Recheck" switch will dim during a system check.


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*a: Device Name List No. 1 Description
Name Component Connection Method
AVN Navigation receiver assembly -
Rr-TV Television display assembly*1 Communication line for AVC-LAN
DSP-AMP Stereo component amplifier assembly Communication line for AVC-LAN
CAMERA-C Parking assist ECU*2 Communication line for AVC-LAN

*1: w/ Rear Seat Entertainment System

*2: w/ Multi-terrain Monitor System


*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
NCON The device was previously present, but does not respond in diagnostic mode. - Check power supply wire harness of the device.
- Check the AVC-LAN of the device.
NRES The device responds in diagnostic mode, but gives no DTC information. - Check power supply wire harness of the device.
- Check the AVC-LAN of the device.

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness
VTR/RR Video (video adapter) terminal Vehicle wire harness


b.
E276983E01
1.934,0.107 2.094,0.254 0.161,0.147 10 *a 1.051,0.107 1.212,0.254 0.161,0.147 10 *b 0.266,0.583 0.427,0.730 0.161,0.147 10 *c 0.805,1.861 0.965,2.007 0.161,0.147 10 *d 1.977,1.861 2.137,2.007 0.161,0.147 10 *e 2.604,1.861 2.764,2.007 0.161,0.147 10 *f 1.73,0.42 1.968,0.228 false 1.398,0.591 1.249,0.225 false 0.702,0.672 0.473,0.672 false 0.888,1.096 0.888,1.843 false 2.08,1.004 2.08,1.835 false 2.67,1.74 2.67,1.838 false

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Timestamp The time and date of history DTCs are displayed (The year is displayed in 2-digit format).
*f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E287734

Read the system check result.

i.

If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", this means that no DTCs are output.

·

When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the steps above to view the results of other devices.







DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E287735

Clear DTCs

i.

Press the "Memory CLR" switch for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.





b.
E287736

Recheck

i.

Press the "Recheck" switch.


ii.
E287737

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the engine switch off.