1.INSTALL DIFFERENTIAL RING GEAR
Clean the contact surfaces of the rear differential case sub-assembly and ring gear.
Clean the ring gear set bolt hole.
Heat the differential ring gear to approximately 100°C (212°F) in boiling water.
Carefully take the differential ring gear out of the boiling water.
Use thick gloves to protect your hands as the differential ring gear is hot.
| *a | 100°C (212°F) |
Secure the rear differential case sub-assembly between aluminum plates in a vise.
Do not overtighten the vise.
After the moisture on the differential ring gear has completely evaporated, quickly install the differential ring gear to the rear differential case sub-assembly.
Align the matchmarks on the differential ring gear and rear differential case sub-assembly.
| *a | Matchmark |
After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and Temporarily install them.
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
Diametrically tighten the 12 bolts uniformly in several passes.
41301A
2.INSTALL REAR DIFFERENTIAL CASE BEARING
Using SST and a press, press the rear differential case bearing (inner) onto the rear differential case sub-assembly.
3.INSPECT DIFFERENTIAL RING GEAR RUNOUT
Install the rear differential case sub-assembly to the carrier and install the 2 plate washers so that there is no play in the bearing.
Install the 2 bearing caps with the 4 bolts.
Using a dial indicator, measure the runout of the ring gear.
0.07 mm (0.00276 in.)
Remove the 2 bearing caps, 2 plate washers and rear differential case sub-assembly.
41201B
4.INSTALL REAR DRIVE PINION FRONT BEARING
Using SST and a press, press in the roller bearing (outer) to the carrier.
41201A
5.INSTALL REAR DRIVE PINION REAR BEARING
Install the plate washer to the carrier.
First, install a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.
Using SST and a press, press the roller bearing (outer) into the carrier.
41201A
6.INSTALL REAR DRIVE PINION REAR BEARING
Using SST and a press, press the roller bearing (inner) onto the drive pinion.
7.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD
Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.
Install the spacer and oil seal after adjusting the gear contact pattern.
Using SST, install the companion flange.
Before using SST (center bolt), apply hypoid gear oil LSD to its threads and tip.
Using a 30 mm socket wrench, adjust the drive pinion preload by tightening the companion flange nut.
Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).
457 N*m (4660 kgf*cm, 337ft.*lbf) or less
As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten the nut.
Apply hypoid gear oil LSD to drive pinion thread and seat face.
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 0.68 to 2.03 N*m (6.94 to 20.7 kgf*cm, 6.02 to 17.9 in.*lbf) |
| Used bearing | 0.73 to 1.83 N*m (7.45 to 18.6 kgf*cm, 6.46 to 16.1 in.*lbf) |
For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
8.INSTALL DIFFERENTIAL CASE ASSEMBLY
Place the 2 bearing outer races on their respective bearings.
Do not interchange the right and left races.
9.ADJUST RING GEAR BACKLASH
Install the plate washer on the side without the ring gear teeth.
Make sure that the ring gear has backlash.
Using a dial indicator, while holding the companion flange, measure the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
Select a plate washer for the side without the ring gear teeth using the backlash as a reference.
Select a plate washer for the side with the ring gear teeth so that there is no clearance between the outer race and case.
Using a plastic-faced hammer, install the plate washer for the side with the ring gear teeth.
Using a dial indicator, while holding the companion flange, measure the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
There should be no clearance between the plate washer and case.
Make sure that there is ring gear backlash.
10.ADJUST SIDE BEARING PRELOAD
Remove the ring gear teeth side plate washer and, using a micrometer, measure the thickness.
Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.
Select a washer which can be pressed in 2/3 of the full amount with your finger.
Recheck the ring gear backlash.
0.10 to 0.20 mm (0.00394 to 0.00788 in.)
If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.
An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.
| Mark | Thickness | Mark | Thickness |
|---|---|---|---|
| 70 | 2.05 to 2.07 mm (0.0807 to 0.0815 in.) | 62 | 2.41 to 2.43 mm (0.0949 to 0.0957 in.) |
| 71 | 2.07 to 2.09 mm (0.0815 to 0.0823 in.) | 63 | 2.43 to 2.45 mm (0.0957 to 0.0965 in.) |
| 72 | 2.09 to 2.11 mm (0.0823 to 0.0831 in.) | 64 | 2.45 to 2.47 mm (0.0965 to 0.0972 in.) |
| 73 | 2.11 to 2.13 mm (0.0831 to 0.0839 in.) | 65 | 2.47 to 2.49 mm (0.0972 to 0.0980 in.) |
| 74 | 2.13 to 2.15 mm (0.0839 to 0.0846 in.) | 66 | 2.49 to 2.51 mm (0.0980 to 0.0988 in.) |
| 75 | 2.15 to 2.17 mm (0.0846 to 0.0854 in.) | 67 | 2.51 to 2.53 mm (0.0988 to 0.0996 in.) |
| 76 | 2.17 to 2.19 mm (0.0854 to 0.0862 in.) | 68 | 2.53 to 2.55 mm (0.0996 to 0.1004 in.) |
| 77 | 2.19 to 2.21 mm (0.0862 to 0.0870 in.) | 69 | 2.55 to 2.57 mm (0.1004 to 0.1012 in.) |
| 78 | 2.21 to 2.23 mm (0.0870 to 0.0878 in.) | 01 | 2.57 to 2.59 mm (0.1012 to 0.1020 in.) |
| 79 | 2.23 to 2.25 mm (0.0878 to 0.0886 in.) | 32 | 2.59 to 2.61 mm (0.1020 to 0.1028 in.) |
| 80 | 2.25 to 2.27 mm (0.0886 to 0.0894 in.) | 33 | 2.61 to 2.63 mm (0.1028 to 0.1035 in.) |
| 81 | 2.27 to 2.29 mm (0.0894 to 0.0902 in.) | 03 | 2.63 to 2.65 mm (0.1035 to 0.1043 in.) |
| 82 | 2.29 to 2.31 mm (0.0902 to 0.0909 in.) | 34 | 2.65 to 2.67 mm (0.1043 to 0.1051 in.) |
| 83 | 2.31 to 2.33 mm (0.0909 to 0.0917 in.) | 35 | 2.67 to 2.69 mm (0.1051 to 0.1059 in.) |
| 84 | 2.33 to 2.35 mm (0.0917 to 0.0925 in.) | 05 | 2.69 to 2.71 mm (0.1059 to 0.1067 in.) |
| 85 | 2.35 to 2.37 mm (0.0925 to 0.0933 in.) | 36 | 2.71 to 2.73 mm (0.1067 to 0.1075 in.) |
| 86 | 2.37 to 2.39 mm (0.0933 to 0.0941 in.) | 37 | 2.73 to 2.75 mm (0.1075 to 0.1083 in.) |
| 87 | 2.39 to 2.41 mm (0.0941 to 0.0949] in.) | 07 | 2.75 to 2.77 mm (0.1083 to 0.1091 in.) |
11.INSTALL BEARING CAP
| *a | Matchmark |
Align the matchmarks on the cap and carrier.
Install the 2 bearing caps with the 4 bolts.
After rotating the ring gear 5 times or more, recheck the backlash.
12.INSPECT DIFFERENTIAL RING GEAR RUNOUT
Using a dial indicator, measure the runout of the ring gear.
0.07 mm (0.00276 in.)
If the runout is more than the maximum, replace the ring gear.
13.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)
If necessary, disassemble and inspect the differential.
14.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.
Hold the companion flange firmly in place and rotate the ring gear in both directions.
Inspect the tooth contact pattern.
If the teeth are not engaged properly, use the following chart to select a proper washer.
| *1 | Plate Washer |
| *2 | Rear Drive Pinion Rear Tapered Roller Bearing (Outer) |
| Mark | Thickness | Mark | Thickness |
|---|---|---|---|
| 29 | 1.84 to 1.86 mm (0.0724 to 0.0732 in.) | 53 | 2.08 to 2.10 mm (0.0819 to 0.0827 in.) |
| 31 | 1.86 to 1.88 mm (0.0732 to 0.0740 in.) | 55 | 2.10 to 2.12 mm (0.0827 to 0.0834 in.) |
| 33 | 1.88 to 1.90 mm (0.0740 to 0.0748 in.) | 57 | 2.12 to 2.14 mm (0.0835 to 0.0843 in.) |
| 35 | 1.90 to 1.92 mm (0.0748 to 0.0756 in.) | 59 | 2.14 to 2.16 mm (0.0843 to 0.0850 in.) |
| 37 | 1.92 to 1.94 mm (0.0756 to 0.0764 in.) | 61 | 2.16 to 2.18 mm (0.0850 to 0.0858 in.) |
| 39 | 1.94 to 1.96 mm (0.0764 to 0.0772 in.) | 63 | 2.18 to 2.20 mm (0.0858 to 0.0866 in.) |
| 41 | 1.96 to 1.98 mm (0.0772 to 0.0780in.) | 65 | 2.20 to 2.22 mm (0.0866 to 0.0874 in.) |
| 43 | 1.98 to 2.00 mm (0.0780 to 0.0787 in.) | 67 | 2.22 to 2.24 mm (0.0874 to 0.0882 in.) |
| 45 | 2.00 to 2.02 mm (0.0787 to 0.0795 in.) | 69 | 2.24 to 2.26 mm (0.0882 to 0.0890 in.) |
| 47 | 2.02 to 2.04 mm (0.0795 to 0.0803 in.) | 71 | 2.26 to 2.28 mm (0.0890 to 0.0898 in.) |
| 49 | 2.04 to 2.06 mm (0.0803 to 0.0811 in.) | 73 | 2.28 to 2.30 mm (0.0898 to 0.0906 in.) |
| 51 | 2.06 to 2.08 mm (0.0811 to 0.0818 in.) | 75 | 2.30 to 2.32 mm (0.0906 to 0.0913 in.) |
41204B
15.REMOVE REAR DRIVE PINION NUT
Using SST to hold the companion flange in place, remove the nut.
41204
16.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
41214
17.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
41201B
18.REMOVE REAR DRIVE PINION FRONT BEARING (INNER)
41201B
19.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)
41231
20.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new bearing spacer to the drive pinion.
41115
21.INSTALL DIFFERENTIAL OIL STORAGE RING
Using SST, tap in a new oil storage ring.
41201B
22.INSTALL REAR DRIVE PINION FRONT BEARING (INNER)
41201B
23.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)
41214
24.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
41201C
25.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
Apply MP grease to a new oil seal.
Using SST and a hammer, tap in the oil seal.
-0.3 to 0.3 mm (-0.0118 to 0.0118 in.)
41204
26.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using SST, install the companion flange to the drive pinion.
| *a | Turn |
| *b | Hold |
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Coat the threads of a new nut with hypoid gear oil.
Using SST to hold the companion flange in place, then slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).
457 N*m (4660 kgf*cm, 337ft.*lbf) or less
27.INSPECT DRIVE PINION PRELOAD
Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.
| Item | Specified Condition |
|---|---|
| New bearing | 0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf) |
| Used bearing | 0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf) |
If the result not as specified, replace the bearing spacer.
If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.
457 N*m (4660 kgf*cm, 337ft.*lbf) or less
If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.
Do not loosen the pinion nut to reduce the preload.
28.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)
If necessary, disassemble and inspect the differential.
29.INSPECT DIFFERENTIAL RING GEAR BACKLASH
Using a dial indicator, check the backlash of the ring gear.
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.
Perform the measurement at 3 or more positions around the circumference of the ring gear.
41204
30.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Using a dial indicator, measure the runout of the drive pinion companion flange vertically and laterally.
30 mm (1.18 in.)
| Item | Specified Condition |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
| *a | Vertical Runout |
| *b | Lateral Runout |
If the runout is more than the maximum, replace the companion flange.
41204B
31.STAKE DRIVE PINION NUT
Using a chisel and hammer, stake the nut.