Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Radio Receiver and Extension Module  


DESCRIPTION

This circuit sends a microphone voice signal from the navigation ECU to the radio and display receiver assembly.

Using this circuit, the navigation ECU disables the microphone function of the radio and display receiver assembly to receive a microphone voice signal from the telephone microphone assembly.

WIRING DIAGRAM

E292627E03
0.719,1.896 2.448,2.26 1.729,0.365 10 false Radio and Display Receiver Assembly 5.51,1.906 6.625,2.135 1.115,0.229 10 false Navigation ECU 1.365,1.323 1.969,1.49 0.604,0.167 10 false SGND 1.396,0.833 1.813,1 0.417,0.167 10 false MCO- 5.708,1.323 6.396,1.49 0.688,0.167 10 false SGND 5.698,0.865 6.115,1.031 0.417,0.167 10 false MIC- 5.698,0.385 6.115,0.552 0.417,0.167 10 false MIC+ 1.365,0.354 1.823,0.521 0.458,0.167 10 false MCO+ 0.729,1.74 1.083,1.906 0.354,0.167 10 false z12 5.521,1.729 5.875,1.896 0.354,0.167 10 false z13 5.417,1.229 5.646,1.396 0.229,0.167 10 false 18 5.406,0.74 5.635,0.906 0.229,0.167 10 false 17 5.406,0.281 5.635,0.448 0.229,0.167 10 false 16 1.885,1.219 2.115,1.385 0.229,0.167 10 false 1 1.885,0.729 2.115,0.896 0.229,0.167 10 false 6 1.885,0.26 2.115,0.427 0.229,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the z12 radio and display receiver assembly connector.


b.

Disconnect the z13 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-5 (MCO+) - z13-16 (MIC+) Always Below 1 Ω
z12-6 (MCO-) - z13-17 (MIC-) Always Below 1 Ω
z12-1 (SGND) - z13-18 (SGND) Always Below 1 Ω
z12-5 (MCO+) - Body ground Always 10 kΩ or higher
z12-6 (MCO-) - Body ground Always 10 kΩ or higher
z12-1 (SGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR