Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260954 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


B118684C37
1.76,0.833 2.208,1.146 0.448,0.313 1.854,0.896 2.219,1.125 0.365,0.229 10 false G35 0.281,0.125 0.51,0.292 0.229,0.167 10 false *a
*a Component without harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
- -


a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G35-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G35-3 (IGE) - G35-1 (GND) Input W - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*

·

Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Pulse generation (see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G35-4 (SLP1) - G35-1 (GND) Output SB - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start
·

Sensor Value


G35-5 (LIN) - G35-1 (GND) Input/Output G - W-B LIN communication line - -
Entry&Start
·

Steering Lock Start Cond


G35-6 (IG2) - G35-1 (GND) Input W - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator or upper bracket assembly) Engine switch off → Engine switch on (IG) Below 1 V → 11 to 14 V -
G35-7 (B) - Body ground Input G - Body ground Power source Always 11 to 14 V -

*: for Automatic Transmission


NOTICE:

There is 1 motor and 2 sensors built into the steering lock actuator or upper bracket assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transmission





i.
C221561C19
0.292,0.396 1.698,0.563 1.406,0.167 1.521,1.583 2.49,1.708 0.969,0.125 2.292,0.448 2.719,0.604 0.427,0.156 2.083,1.708 2.167,1.99 2.167,1.99 2.219,1.99 false 1.698,0.438 2.813,0.198 2.813,0.198 2.885,0.198 false 2.802,0.198 2.604,0.448 false 2.917,1.583 3.385,1.958 0.469,0.375 10 GND 2.271,1.906 2.76,2.052 0.49,0.146 10 *b 2.948,0.104 3.313,0.333 0.365,0.229 10 *a
*a Steering Lock Motor not Operating
*b Steering Lock Motor Operating


Waveform

Item Content
Tester Connection G35-3 (IGE) - G35-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*

·

Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG)

·

After above conditions met, engine switch turned off



*: for Automatic Transmission