When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2784 | Antenna Coil Open / Short | The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*1).
·
Terminal AGND, VC5, TXCT or CODE circuit is open (includes disconnection of the engine switch). ·
The transponder key amplifier coil built into the engine switch is open. |
·
Engine switch ·
Harness or connector ·
Certification ECU (smart key ECU assembly) |
DTC output confirmation operation:
With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted. |
*1: Only output while a malfunction is present.
*2: for Automatic Transmission
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P* | - |
*: for Automatic Transmission
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | - |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| DTC B2784 is not output. | A |
| DTC B2784 is output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Engine Switch) |
*b | Waveform |
| *c | Waveform (detail) | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G206-8 (CODE) - G206-6 (AGND) | Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch* | 1 V/DIV., 20 ms./DIV. | Pulse generation
(See waveform) |
| 2 V/DIV., 100 μs./DIV. | Pulse generation
(See waveform (detail)) |
*: Remove the transmitter battery before performing this inspection.
The waveform is similar to that shown in the illustration
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2TR-FE
Click hereEngine / Hybrid System>2TR-FE (STARTING)>ENGINE SWITCH>REMOVAL
for 1GR-FE (for LHD)
Click hereEngine / Hybrid System>1GR-FE (STARTING)>ENGINE SWITCH(for LHD)>REMOVAL
for 1GR-FE (for RHD)
Click hereEngine / Hybrid System>1GR-FE (STARTING)>ENGINE SWITCH (for RHD)>REMOVAL
for 1KD-FTV (for LHD)
Click hereEngine / Hybrid System>1KD-FTV (STARTING)>ENGINE SWITCH (for LHD)>REMOVAL
for 1KD-FTV (for RHD)
Click hereEngine / Hybrid System>1KD-FTV (STARTING)>ENGINE SWITCH (for RHD)>REMOVAL
for 1GD-FTV (for LHD)
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>ENGINE SWITCH(for LHD)>REMOVAL
for 1GD-FTV (for RHD)
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>ENGINE SWITCH (for RHD)>REMOVAL