Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B278A Short to GND in Immobiliser System Power Source Circuit A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*1).
·

Engine switch

·

Harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*1: Only output while a malfunction is present.

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P* -

*: for Automatic Transmission


Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

E305785E42
1.5,0.781 2.021,1.24 0.521,0.458 10 false VC5 1.917,0.677 2.438,1.135 0.521,0.458 10 false 10 1.479,1.292 2,1.75 0.521,0.458 10 false TXCT 1.396,1.708 1.917,2.167 0.521,0.458 10 false CODE 1.938,1.198 2.458,1.656 0.521,0.458 10 false 7 1.938,1.719 2.458,2.177 0.521,0.458 10 false 8 1.938,2.219 2.458,2.677 0.521,0.458 10 false 6 1.406,2.219 1.927,2.677 0.521,0.458 10 false AGND 0.219,3.052 0.656,3.24 0.438,0.188 10 false G206 0.219,3.208 1.771,3.479 1.552,0.271 10 false Engine Switch 4.99,0.677 5.51,1.135 0.521,0.458 10 false 15 5,1.198 5.521,1.656 0.521,0.458 10 false 14 5,1.719 5.521,2.177 0.521,0.458 10 false 13 5,2.229 5.521,2.688 0.521,0.458 10 false 12 6.219,0.292 6.74,0.75 0.521,0.458 10 false 5 V 5.115,3.021 5.635,3.229 0.521,0.208 10 false G215 5.146,3.198 6.677,3.667 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.688 5.781,1.146 0.521,0.458 10 false VC5 5.26,1.188 5.781,1.646 0.521,0.458 10 false TXCT 5.25,1.719 5.771,2.177 0.521,0.458 10 false CODE 5.25,2.229 5.771,2.688 0.521,0.458 10 false AGND 6.156,1.542 6.677,2 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B271009C22
1.26,0.156 1.729,0.479 0.469,0.323 1.833,1.656 2.406,2.042 true 1.208,1.656 0.635,2.052 true 1.323,0.24 1.792,0.49 0.469,0.25 10 false G206 0.083,0.083 0.344,0.333 0.26,0.25 10 false *a 2.969,3.292 3.385,3.563 0.417,0.271 10 false GND 0.323,2.021 0.719,2.25 0.396,0.229 10 false VC5 2.448,1.979 3.01,2.208 0.563,0.229 10 false AGND 0.083,2.281 0.396,2.479 0.313,0.198 10 false *b
*a Component with harness connector
(Engine Switch)
*b Waveform


Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the engine switch side.


Measurement Condition
Item Content
Tester Connection G206-10 (VC5) - G206-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G206 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-15 (VC5) - G206-10 (VC5) Always Below 1 Ω
G215-12 (AGND) - G206-6 (AGND) Always Below 1 Ω
G206-10 (VC5) - Body ground Always 10 kΩ or higher
G215-15 (VC5) - Body ground Always 10 kΩ or higher
G206-6 (AGND) - Body ground Always 10 kΩ or higher
G215-12 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the G206 engine switch connector.


c.

Measure the voltage according to the value(s) in the table below.

B343119C86
5.052,0.26 5.479,0.49 0.427,0.229 5.906,2.198 5.771,2.198 5.771,2.198 5.552,1.115 true 6.563,2.177 6.417,2.177 6.417,2.177 5.938,1.104 true 6.615,2.104 7.073,2.302 0.458,0.198 10 false AGND 5.104,0.292 5.563,0.49 0.458,0.198 10 false G215 5.958,2.125 6.417,2.323 0.458,0.198 10 false VC5 0.167,0.104 0.625,0.302 0.458,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G215-15 (VC5) - G215-12 (AGND) Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V


*1: for Automatic Transmission

*2: for Manual Transmission



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ASSEMBLY)