Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B442701E05
2.167,2.333 5,2.5 2.833,0.167 10 false *1: for 1GR-FE (for Automatic Transmission) 2.167,2.604 7.146,2.833 4.979,0.229 10 false *2: for 1GR-FE (for Manual Transmission) 2.167,2.896 3.5,3.083 1.333,0.188 10 false *3: for 2TR-FE 2.167,3.167 4,3.333 1.833,0.167 10 false *4: for 1KD-FTV 2.167,3.438 3.75,3.667 1.583,0.229 10 false *5: for 1GD-FTV 4.969,2.823 5.583,3.156 0.615,0.333 10 false G207 4.99,3 6.563,3.448 1.573,0.448 10 false ID Code Box (Immobiliser Code ECU) 2.073,1.01 2.688,1.344 0.615,0.333 10 false G56 1.688,0.906 2.302,1.24 0.615,0.333 10 false IMO 1.75,1.813 2.365,2.146 0.615,0.333 10 false IMI 1.469,1.469 2.083,1.802 0.615,0.333 10 false +B 6.146,0.24 6.76,0.573 0.615,0.333 10 false +B 2.073,1.917 2.688,2.25 0.615,0.333 10 false G56 2.469,1.01 3.083,1.344 0.615,0.333 10 false G56 2.469,1.917 3.083,2.25 0.615,0.333 10 false G56 2.833,1.01 3.448,1.344 0.615,0.333 10 false G181 2.823,1.917 3.438,2.25 0.615,0.333 10 false G181 3.26,1.01 3.875,1.344 0.615,0.333 10 false G58 3.26,1.917 3.875,2.25 0.615,0.333 10 false G58 3.625,1.01 4.24,1.344 0.615,0.333 10 false G185 3.625,1.917 4.24,2.25 0.615,0.333 10 false G185 5.177,0.906 5.792,1.24 0.615,0.333 10 false EFII 5.188,1.823 5.802,2.156 0.615,0.333 10 false EFIO 2.094,0.792 2.708,1.125 0.615,0.333 10 false 8*1 2.052,1.708 2.667,2.042 0.615,0.333 10 false 10*1 2.448,0.792 3.063,1.125 0.615,0.333 10 false 20*2 2.448,1.698 3.063,2.031 0.615,0.333 10 false 14*2 2.875,0.792 3.49,1.125 0.615,0.333 10 false 9*3 2.844,1.698 3.458,2.031 0.615,0.333 10 false 10*3 3.25,0.792 3.865,1.125 0.615,0.333 10 false 29*4 3.25,1.698 3.865,2.031 0.615,0.333 10 false 28*4 3.646,0.792 4.26,1.125 0.615,0.333 10 false 17*5 3.646,1.698 4.26,2.031 0.615,0.333 10 false 16*5 4.938,0.896 5.552,1.229 0.615,0.333 10 false 3 4.958,1.823 5.573,2.156 0.615,0.333 10 false 4 0.917,2.865 1.531,3.198 0.615,0.333 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ID code box (immobiliser code ECU) or ECM, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

4.INSPECT ECM (TERMINAL IMO)

C

4.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B492118C01
2.115,0.135 2.448,0.333 0.333,0.198 4.667,1.458 5.083,1.656 0.417,0.198 4.188,2.75 4.604,2.948 0.417,0.198 1.833,4.135 2.167,4.333 0.333,0.198 5.979,5.667 6.396,5.865 0.417,0.198 2.448,0.719 2.688,0.24 2.688,0.24 2.781,0.24 true 2.458,1.021 2.708,1.458 2.708,1.458 2.813,1.458 true 5.229,1.583 5.146,1.583 5.146,1.583 5.031,2.125 true 4.76,2.885 4.677,2.885 4.677,2.885 4.604,3.469 true 1.875,5.271 1.781,5.729 1.781,5.729 1.677,5.729 true 5.813,5.792 5.906,5.792 5.906,5.792 5.792,6.271 true 0.104,0.25 0.438,0.438 0.333,0.188 12 false *A 0.094,1.469 0.719,1.656 0.625,0.188 12 false *B (*E) 0.104,4.25 0.521,4.458 0.417,0.208 12 false *C 0.104,5.75 0.469,5.927 0.365,0.177 12 false *D 0.104,0.417 0.417,0.573 0.313,0.156 10 false *a 2.906,8.385 3.219,8.542 0.313,0.156 10 false *b 0.083,2.875 0.677,3.083 0.594,0.208 12 false *B (*F) 0.979,8.302 1.438,8.5 0.458,0.198 10 false GND 0.104,1.656 0.417,1.813 0.313,0.156 10 false *a 0.104,3.063 0.417,3.219 0.313,0.156 10 false *a 0.094,4.406 0.406,4.563 0.313,0.156 10 false *a 0.104,5.917 0.417,6.073 0.313,0.156 10 false *a 2.146,0.156 2.604,0.354 0.458,0.198 10 false G56 2.865,0.156 3.448,0.354 0.583,0.198 10 false IMO (*E) 2.823,1.375 3.406,1.573 0.583,0.198 10 false IMO (*F) 4.708,1.469 5.167,1.667 0.458,0.198 10 false G181 4.229,2.76 4.688,2.958 0.458,0.198 10 false G181 5.271,1.49 5.854,1.688 0.583,0.198 10 false IMO 4.802,2.813 5.385,3.01 0.583,0.198 10 false IMO 1.865,4.156 2.323,4.354 0.458,0.198 10 false G58 1.406,5.635 1.781,5.813 0.375,0.177 10 false IMO 6.01,5.677 6.469,5.875 0.458,0.198 10 false G185 5.552,5.719 5.927,5.896 0.375,0.177 10 false IMO
*A for 1GR-FE *B for 2TR-FE
*C for 1KD-FTV *D for 1GD-FTV
*E for Automatic Transmission *F for Manual Transmission
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G56-8 (IMO) - Body ground*1
G56-20 (IMO) - Body ground*2
G181-9 (IMO) - Body ground*3
G58-29 (IMO) - Body ground*4
G185-17 (IMO) - Body ground*5
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

*1: for 1GR-FE (for Automatic Transmission)

*2: for 1GR-FE (for Manual Transmission)

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV


OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

5.INSPECT ECM (TERMINAL IMI)

B

11.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

8.REPLACE ECM
5.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B492119C01
2.042,0.135 2.375,0.333 0.333,0.198 4.656,1.427 5.073,1.625 0.417,0.198 4.167,2.75 4.583,2.948 0.417,0.198 1.906,4.125 2.24,4.323 0.333,0.198 5.979,5.667 6.396,5.865 0.417,0.198 2.219,0.708 2.573,0.24 2.573,0.24 2.656,0.24 true 2.458,0.906 2.656,1.448 2.656,1.448 2.729,1.448 true 4.969,2.135 5.198,1.542 5.198,1.542 5.292,1.542 true 4.5,3.479 4.74,2.885 4.74,2.885 4.844,2.885 true 1.656,5.719 1.75,5.719 1.75,5.719 1.938,5.271 true 5.885,6.302 5.76,5.75 5.76,5.75 5.667,5.75 true 0.083,0.208 0.49,0.406 0.406,0.198 12 false *A 0.104,2.844 0.75,3.042 0.646,0.198 12 false *B (*F) 0.083,4.229 0.458,4.427 0.375,0.198 12 false *C 0.104,5.792 0.5,6.042 0.396,0.25 12 false *D 0.104,0.365 0.417,0.521 0.313,0.156 10 false *a 3.333,8.365 3.646,8.521 0.313,0.156 10 false *b 0.104,1.5 0.688,1.74 0.583,0.24 12 false *B (*E) 0.104,1.667 0.417,1.823 0.313,0.156 10 false *a 0.104,3.01 0.417,3.167 0.313,0.156 10 false *a 0.094,4.396 0.406,4.552 0.313,0.156 10 false *a 0.104,5.938 0.417,6.094 0.313,0.156 10 false *a 2.094,0.156 2.479,0.333 0.385,0.177 10 false G56 4.708,1.448 5.094,1.625 0.385,0.177 10 false G181 4.208,2.771 4.594,2.948 0.385,0.177 10 false G181 1.958,4.135 2.344,4.313 0.385,0.177 10 false G58 6.01,5.688 6.396,5.865 0.385,0.177 10 false G185 1,8.281 1.385,8.458 0.385,0.177 10 false GND 4.906,2.802 5.198,3 0.292,0.198 10 false IMI 2.802,1.365 3.344,1.563 0.542,0.198 10 false IMI (*F) 2.677,0.167 3.219,0.365 0.542,0.198 10 false IMI (*E) 5.385,1.438 5.677,1.635 0.292,0.198 10 false IMI 1.438,5.635 1.729,5.833 0.292,0.198 10 false IMI 5.427,5.677 5.719,5.875 0.292,0.198 10 false IMI
*A for 1GR-FE *B for 2TR-FE
*C for 1KD-FTV *D for 1GD-FTV
*E for Automatic Transmission *F for Manual Transmission
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G56-10 (IMI) - Body ground*1
G56-14 (IMI) - Body ground*2
G181-10 (IMI) - Body ground*3
G58-28 (IMI) - Body ground*4
G185-16 (IMI) - Body ground*5
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

*1: for 1GR-FE (for Automatic Transmission)

*2: for 1GR-FE (for Manual Transmission)

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

6.REGISTER ECU COMMUNICATION ID

NG

8.REPLACE ECM
6.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ECM
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

B492120C01
1.104,0.448 1.521,0.667 0.417,0.219 1.104,0.167 1.521,0.385 0.417,0.219 5.583,0.5 6,0.719 0.417,0.219 3.313,0.5 3.729,0.719 0.417,0.219 1.604,1.771 1.813,2.313 1.813,2.313 1.927,2.313 true 0.906,2.219 0.99,2.219 0.99,2.219 1.156,1.375 true 0.917,2.521 1,2.521 1,2.521 1.177,1.635 true 2.76,0.75 2.844,0.75 2.844,0.75 3.26,1.417 true 6.333,1.396 6.563,1.167 6.563,1.167 6.677,1.167 true 0.354,0.167 0.708,0.375 0.354,0.208 12 false *A 2.604,0.167 2.969,0.365 0.365,0.198 12 false *B 0.354,0.406 0.708,0.625 0.354,0.219 12 false *C 4.917,0.167 5.281,0.354 0.365,0.188 12 false *D 2.854,0.167 3.167,0.323 0.313,0.156 10 false *a 5.167,0.177 5.479,0.333 0.313,0.156 10 false *a 0.604,0.177 0.917,0.333 0.313,0.156 10 false *a 1.167,0.198 1.542,0.396 0.375,0.198 10 false G56 1.167,0.49 1.542,0.688 0.375,0.198 10 false G58 1.573,0.198 2.083,0.396 0.51,0.198 10 false *A 1.573,0.479 1.885,0.635 0.313,0.156 10 false *C 1.979,2.24 2.594,2.438 0.615,0.198 10 false IMO (*C) 3.354,0.521 3.729,0.719 0.375,0.198 10 false G181 0.073,2.427 1.031,2.667 0.958,0.24 10 false IMO (*A, *F) 0.094,2.125 0.99,2.417 0.896,0.292 10 false IMO (*A, *E) 2.469,0.677 2.927,0.875 0.458,0.198 10 false IMO 5.615,0.521 5.99,0.719 0.375,0.198 10 false G185 6.708,1.083 7.052,1.302 0.344,0.219 10 false IMO
*A for 1GR-FE *B for 2TR-FE
*C for 1KD-FTV *D for 1GD-FTV
*E for Automatic Transmission *F for Manual Transmission
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result
G56-8 (IMO) - Body ground*1
G56-20 (IMO) - Body ground*2
G181-9 (IMO) - Body ground*3
G58-29 (IMO) - Body ground*4
G185-17 (IMO) - Body ground*5
Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for 1GR-FE (for Automatic Transmission)

*2: for 1GR-FE (for Manual Transmission)

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

8.REPLACE ECM
12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G207 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for Automatic Transmission)
Tester Connection Condition Specified Condition
G207-3 (EFII) - G56-8 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-8 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE (for Manual Transmission)
Tester Connection Condition Specified Condition
G207-3 (EFII) - G56-20 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G56-14 (IMI) Always Below 1 Ω
G56-20 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G56-14 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G207-3 (EFII) - G181-9 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G181-9 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G181-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G207-3 (EFII) - G58-29 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G58-29 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G58-28 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G207-3 (EFII) - G185-17 (IMO) Always Below 1 Ω
G207-4 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G185-17 (IMO) - Body ground Always 10 kΩ or higher
G207-3 (EFII) - Body ground Always 10 kΩ or higher
G185-16 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the ID code box (immobiliser code ECU).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 1GR-FE)
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 1GD-FTV)



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG (for 1GR-FE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 1GD-FTV)