Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Harness or connector

·

ID code box (immobiliser code ECU)

·

ECM


DTC output confirmation operation:

Turn the engine switch on (IG) and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B442700E03
2.115,1.396 7.156,1.615 5.042,0.219 10 false *1: for 1GR-FE (for Automatic Transmission) 2.115,1.667 7.156,1.885 5.042,0.219 10 false *2: for 1GR-FE (for Manual Transmission) 2.115,1.948 7.156,2.167 5.042,0.219 10 false *3: for 2TR-FE 2.115,2.208 7.156,2.427 5.042,0.219 10 false *4: for 1KD-FTV 2.115,2.469 7.156,2.635 5.042,0.167 10 false *5: for 1GD-FTV 1.938,0.958 2.396,1.156 0.458,0.198 10 false G56 2.333,0.958 2.792,1.156 0.458,0.198 10 false G56 2.698,0.958 3.156,1.156 0.458,0.198 10 false G181 3.135,0.958 3.594,1.156 0.458,0.198 10 false G58 3.479,0.958 3.938,1.156 0.458,0.198 10 false G185 1.917,0.75 2.375,0.948 0.458,0.198 10 false 10*1 2.313,0.75 2.771,0.948 0.458,0.198 10 false 14*2 2.719,0.75 3.177,0.948 0.458,0.198 10 false 10*3 3.104,0.75 3.563,0.948 0.458,0.198 10 false 28*4 3.51,0.75 3.969,0.948 0.458,0.198 10 false 16*5 1.615,0.844 2.073,1.042 0.458,0.198 10 false IMI 1.323,0.531 1.781,0.729 0.458,0.198 10 false +B 5.01,0.844 5.469,1.042 0.458,0.198 10 false EFIO 4.75,0.844 5.208,1.042 0.458,0.198 10 false 4 5,1.875 5.458,2.073 0.458,0.198 10 false G207 5,2.052 6.583,2.427 1.583,0.375 10 false ID Code Box (Immobiliser Code ECU) 0.844,1.917 1.302,2.115 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ID code box (immobiliser code ECU) or ECM, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B279A and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (TERMINAL IMI)

NG

CONNECT CONNECTORS PROPERLY

2.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B492119C01
2.042,0.135 2.375,0.333 0.333,0.198 4.656,1.427 5.073,1.625 0.417,0.198 4.167,2.75 4.583,2.948 0.417,0.198 1.906,4.125 2.24,4.323 0.333,0.198 5.979,5.667 6.396,5.865 0.417,0.198 2.219,0.708 2.573,0.24 2.573,0.24 2.656,0.24 true 2.458,0.906 2.656,1.448 2.656,1.448 2.729,1.448 true 4.969,2.135 5.198,1.542 5.198,1.542 5.292,1.542 true 4.5,3.479 4.74,2.885 4.74,2.885 4.844,2.885 true 1.656,5.719 1.75,5.719 1.75,5.719 1.938,5.271 true 5.885,6.302 5.76,5.75 5.76,5.75 5.667,5.75 true 0.083,0.208 0.49,0.406 0.406,0.198 12 false *A 0.104,2.844 0.75,3.042 0.646,0.198 12 false *B (*F) 0.083,4.229 0.458,4.427 0.375,0.198 12 false *C 0.104,5.792 0.5,6.042 0.396,0.25 12 false *D 0.104,0.365 0.417,0.521 0.313,0.156 10 false *a 3.333,8.365 3.646,8.521 0.313,0.156 10 false *b 0.104,1.5 0.688,1.74 0.583,0.24 12 false *B (*E) 0.104,1.667 0.417,1.823 0.313,0.156 10 false *a 0.104,3.01 0.417,3.167 0.313,0.156 10 false *a 0.094,4.396 0.406,4.552 0.313,0.156 10 false *a 0.104,5.938 0.417,6.094 0.313,0.156 10 false *a 2.094,0.156 2.479,0.333 0.385,0.177 10 false G56 4.708,1.448 5.094,1.625 0.385,0.177 10 false G181 4.208,2.771 4.594,2.948 0.385,0.177 10 false G181 1.958,4.135 2.344,4.313 0.385,0.177 10 false G58 6.01,5.688 6.396,5.865 0.385,0.177 10 false G185 1,8.281 1.385,8.458 0.385,0.177 10 false GND 4.906,2.802 5.198,3 0.292,0.198 10 false IMI 2.802,1.365 3.344,1.563 0.542,0.198 10 false IMI (*F) 2.677,0.167 3.219,0.365 0.542,0.198 10 false IMI (*E) 5.385,1.438 5.677,1.635 0.292,0.198 10 false IMI 1.438,5.635 1.729,5.833 0.292,0.198 10 false IMI 5.427,5.677 5.719,5.875 0.292,0.198 10 false IMI
*A for 1GR-FE *B for 2TR-FE
*C for 1KD-FTV *D for 1GD-FTV
*E for Automatic Transmission *F for Manual Transmission
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G56-10 (IMI) - Body ground*1
G56-14 (IMI) - Body ground*2
G181-10 (IMI) - Body ground*3
G58-28 (IMI) - Body ground*4
G185-16 (IMI) - Body ground*5
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

*1: for 1GR-FE (for Automatic Transmission)

*2: for 1GR-FE (for Manual Transmission)

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV


OK:

The waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG




OK

NG

3.CHECK ECM
3.CHECK ECM
a.

Disconnect the G207 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

B492121C01
1.417,0.333 1.75,0.531 0.333,0.198 2.146,0.333 2.479,0.531 0.333,0.198 3.167,0.333 3.5,0.531 0.333,0.198 3.927,0.333 4.26,0.531 0.333,0.198 4.615,0.333 4.948,0.531 0.333,0.198 5.375,0.333 5.708,0.531 0.333,0.198 0.885,1.802 1.302,2 0.417,0.198 2.115,1.802 2.531,2 0.417,0.198 3.417,1.802 3.833,2 0.417,0.198 4.625,1.802 5.042,2 0.417,0.198 5.813,1.802 6.229,2 0.417,0.198 1.292,3.219 1.708,3.417 0.417,0.198 2.646,3.219 3.063,3.417 0.417,0.198 4.167,3.219 4.583,3.417 0.417,0.198 5.5,3.219 5.917,3.417 0.417,0.198 1.063,4.667 1.396,4.865 0.333,0.198 0.76,6.333 1.177,6.531 0.417,0.198 1.885,4.667 2.219,4.865 0.333,0.198 3.198,4.667 3.531,4.865 0.333,0.198 3.948,4.667 4.281,4.865 0.333,0.198 4.708,4.667 5.042,4.865 0.333,0.198 5.646,4.667 5.979,4.865 0.333,0.198 1.823,6.333 2.24,6.531 0.417,0.198 2.885,6.333 3.302,6.531 0.417,0.198 3.896,6.333 4.313,6.531 0.417,0.198 4.958,6.333 5.375,6.531 0.417,0.198 5.969,6.333 6.385,6.531 0.417,0.198 2.448,1.125 2.646,1.688 2.646,1.688 2.74,1.688 true 2.646,0.479 2.531,0.479 2.531,0.479 2.219,0.917 true 5.24,1.896 5.125,1.896 5.125,1.896 4.938,2.469 true 4.813,3.323 4.708,3.323 4.708,3.323 4.49,3.938 true 1.948,5.844 1.76,6.281 1.76,6.281 1.656,6.281 true 5.792,6.469 5.896,6.469 5.896,6.469 5.865,6.948 true 0.083,0.344 0.448,0.583 0.365,0.24 12 false *A 0.083,1.76 0.75,1.948 0.667,0.188 12 false *B (*E) 0.083,4.76 0.448,4.948 0.365,0.188 12 false *C 0.083,6.417 0.51,6.667 0.427,0.25 12 false *D 0.083,0.51 0.396,0.667 0.313,0.156 10 false *a 0.083,3.177 0.719,3.354 0.635,0.177 12 false *B (*F) 0.083,1.927 0.396,2.083 0.313,0.156 10 false *a 0.083,3.344 0.396,3.5 0.313,0.156 10 false *a 0.083,4.917 0.396,5.073 0.313,0.156 10 false *a 0.083,6.583 0.396,6.74 0.313,0.156 10 false *a 1.448,0.344 1.906,0.542 0.458,0.198 10 false G55 2.188,0.344 2.646,0.542 0.458,0.198 10 false G56 3.198,0.344 3.656,0.542 0.458,0.198 10 false C34 3.958,0.344 4.417,0.542 0.458,0.198 10 false C35 4.646,0.344 5.104,0.542 0.458,0.198 10 false C36 5.406,0.344 5.865,0.542 0.458,0.198 10 false C37 0.938,1.813 1.396,2.01 0.458,0.198 10 false C153 2.146,1.813 2.604,2.01 0.458,0.198 10 false C154 3.458,1.823 3.917,2.021 0.458,0.198 10 false C155 4.667,1.823 5.125,2.021 0.458,0.198 10 false G181 5.854,1.823 6.313,2.021 0.458,0.198 10 false G180 1.333,3.24 1.792,3.438 0.458,0.198 10 false C153 2.688,3.24 3.146,3.438 0.458,0.198 10 false C154 4.198,3.24 4.656,3.438 0.458,0.198 10 false G181 5.542,3.24 6,3.438 0.458,0.198 10 false G180 1.094,4.677 1.552,4.875 0.458,0.198 10 false G57 0.802,6.344 1.26,6.542 0.458,0.198 10 false C149 1.917,4.677 2.375,4.875 0.458,0.198 10 false G58 3.229,4.677 3.688,4.875 0.458,0.198 10 false C90 3.99,4.677 4.448,4.875 0.458,0.198 10 false C91 4.74,4.677 5.198,4.875 0.458,0.198 10 false C92 5.688,4.677 6.146,4.875 0.458,0.198 10 false C93 1.875,6.344 2.333,6.542 0.458,0.198 10 false C150 2.927,6.344 3.385,6.542 0.458,0.198 10 false C151 3.938,6.344 4.396,6.542 0.458,0.198 10 false C152 5,6.344 5.458,6.542 0.458,0.198 10 false G184 6.01,6.344 6.469,6.542 0.458,0.198 10 false G185 2.677,0.396 3.323,0.594 0.646,0.198 10 false IMI (*E) 2.771,1.615 3.417,1.813 0.646,0.198 10 false IMI (*F) 4.865,3.24 5.323,3.438 0.458,0.198 10 false IMI 5.25,1.802 5.708,2 0.458,0.198 10 false IMI 1.406,6.188 1.865,6.385 0.458,0.198 10 false IMI 5.552,6.396 6.01,6.594 0.458,0.198 10 false IMI
*A for 1GR-FE *B for 2TR-FE
*C for 1KD-FTV *D for 1GD-FTV
*E for Automatic Transmission *F for Manual Transmission
*a Component with harness connected
(ECM)
- -


Standard Voltage:
for 1GR-FE (for Automatic Transmission)
Tester Connection Condition Specified Condition
G56-10 (IMI) - Body ground Always 11 to 14 V

for 1GR-FE (for Manual Transmission)
Tester Connection Condition Specified Condition
G56-14 (IMI) - Body ground Always 11 to 14 V

for 2TR-FE
Tester Connection Condition Specified Condition
G181-10 (IMI) - Body ground Always 11 to 14 V

for 1KD-FTV
Tester Connection Condition Specified Condition
G58-28 (IMI) - Body ground Always 11 to 14 V

for 1GD-FTV
Tester Connection Condition Specified Condition
G185-16 (IMI) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G56*1, G181*2, G58*3 or G185*4 ECM connector.

*1: for 1GR-FE

*2: for 2TR-FE

*3: for 1KD-FTV

*4: for 1GD-FTV



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for Automatic Transmission)
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE (for Manual Transmission)
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G56-14 (IMI) Always Below 1 Ω
G56-14 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G181-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G58-28 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G185-16 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR