Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on (IG)).

WIRING DIAGRAM

E318144E18
5.604,0.75 6.063,0.948 0.458,0.198 10 false IND 5.406,1.667 5.865,1.865 0.458,0.198 10 false G215 5.427,1.823 6.99,2.25 1.563,0.427 10 false Certification ECU (Smart Key ECU Assembly) 5.302,0.75 5.76,0.948 0.458,0.198 10 false 19 3.042,0.75 3.5,0.948 0.458,0.198 10 false LP 3.365,0.75 3.823,0.948 0.458,0.198 10 false 2 1.573,1.677 2.031,1.875 0.458,0.198 10 false H23 1.604,1.844 4.01,2.271 2.406,0.427 10 false Theft Warning Indicator Light Assembly (Security Indicator Light) 1.698,0.75 2.156,0.948 0.458,0.198 10 false E 1.469,0.75 1.927,0.948 0.458,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Theft warning indicator light assembly (security indicator light) OFF/ON -

OK:

The theft warning indicator light assembly (security indicator light) operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
2.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
a.

Remove the theft warning indicator light assembly (security indicator light).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL


b.

Inspect the theft warning indicator light assembly (security indicator light).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPLACE THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)

3.CHECK HARNESS AND CONNECTOR (THEFT WARNING INDICATOR LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H23-2 (LP) - G215-19 (IND) Always Below 1 Ω
H23-2 (LP) - Body ground Always 10 kΩ or higher
G215-19 (IND) - Body ground Always 10 kΩ or higher
H23-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR