Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, radio and display receiver assembly, telematics transceiver* or speakers.

*: w/ Telematics Transceiver


WIRING DIAGRAM

E296658E24
0.792,0.854 1.406,1.052 0.615,0.198 10 false ADPG 0.854,1.49 1.469,1.688 0.615,0.198 10 false VAR+ 0.875,2.083 1.49,2.281 0.615,0.198 10 false VAL+ 0.979,2.719 1.594,2.917 0.615,0.198 10 false VA- 0.823,3.323 1.438,3.521 0.615,0.198 10 false AGND 1.333,0.75 2.302,1.677 0.969,0.927 10 false 5 1.323,1.365 1.5,1.563 0.177,0.198 10 false 2 1.344,1.969 1.521,2.167 0.177,0.198 10 false 3 1.344,2.583 1.635,2.781 0.292,0.198 10 false 4 1.333,3.198 1.51,3.396 0.177,0.198 10 false 6 0.417,3.667 0.875,3.865 0.458,0.198 10 false H85 0.427,3.823 2.083,4.177 1.656,0.354 10 false No. 1 Stereo Jack Adapter Assembly 3.573,3.458 3.938,3.719 0.365,0.26 10 false * 5.667,0.76 6,0.927 0.333,0.167 10 false 25 5.698,1.354 6.031,1.521 0.333,0.167 10 false 26 5.688,1.979 6.021,2.146 0.333,0.167 10 false 28 5.688,2.604 6.021,2.771 0.333,0.167 10 false 27 5.698,3.188 6.031,3.354 0.333,0.167 10 false 11 5.979,0.865 6.594,1.063 0.615,0.198 10 false ADPG 6.01,1.448 6.625,1.646 0.615,0.198 10 false VAR+ 6,2.104 6.615,2.302 0.615,0.198 10 false VAL+ 5.99,2.698 6.604,2.896 0.615,0.198 10 false VA- 5.979,3.313 6.594,3.51 0.615,0.198 10 false AGND 5.865,3.667 6.479,3.865 0.615,0.198 10 false H51 5.854,3.833 7.052,4.344 1.198,0.51 10 false Radio and Display Receiver Assembly 0.406,4.406 1.604,4.625 1.198,0.219 10 false *: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the H85 No. 1 stereo jack adapter assembly connector.


b.

Disconnect the H51 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-3 (VAL+) - H51-28 (VAL+) Always Below 1 Ω
H85-2 (VAR+) - H51-26 (VAR+) Always Below 1 Ω
H85-4 (VA-) - H51-27 (VA-) Always Below 1 Ω
H85-6 (AGND) - H51-11 (AGND) Always Below 1 Ω
H85-5 (ADPG) - H51-25 (ADPG) Always Below 1 Ω
H85-3 (VAL+) - Body ground Always 10 kΩ or higher
H85-2 (VAR+) - Body ground Always 10 kΩ or higher
H85-4 (VA-) - Body ground Always 10 kΩ or higher
H85-6 (AGND) - Body ground Always 10 kΩ or higher
H85-5 (ADPG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR