Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261004 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display)  Clearance Sonar Main Switch Circuit  


DESCRIPTION

When the back sonar or clearance sonar switch assembly is turned on, the ON signal is input into the ECU.

WIRING DIAGRAM

E194320E06
4.438,1.323 4.708,1.49 0.271,0.167 10 false IND 4.344,0.938 4.667,1.125 0.323,0.188 10 false ECU 2.552,0.938 2.875,1.125 0.323,0.188 10 false IG 4.76,0.688 4.927,0.875 0.167,0.188 10 false 2 5.76,0.823 6.396,1.094 0.635,0.271 10 false CLSW 0.26,0.813 1.115,1.208 0.854,0.396 10 false from IG NO.1 Relay 1.344,0.979 2.281,1.167 0.938,0.188 10 false ECU-IG NO.2 5.615,1.865 6.042,2.052 0.427,0.188 10 false I8 5.594,2.031 6.854,2.396 1.26,0.365 10 false Clearance Warning ECU 2.583,1.698 3.083,1.927 0.5,0.229 10 false G198 2.583,1.854 4.615,2.188 2.031,0.333 10 false Back Sonar or Clearance Sonar Switch Assembly 5.438,0.698 5.698,0.958 0.26,0.26 10 false 19 4.76,1.073 5.083,1.26 0.323,0.188 10 false 4 2.365,0.688 2.646,0.875 0.281,0.188 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.
E379204E01
0.917,1.792 1.406,1.281 true 2.469,1.74 1.979,1.281 true 2.552,1.688 3.01,1.885 0.458,0.198 10 false ECU 0.729,1.719 1.188,1.917 0.458,0.198 10 false IG

Remove the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ECU) - 5 (IG) Pressed (on) Below 1 Ω
2 (ECU) - 5 (IG) Not pressed (off) 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - BATTERY AND BODY GROUND)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - BATTERY AND BODY GROUND)
a.
E379205E01
1.531,0.375 1.938,0.625 0.406,0.25 1.938,1.396 2.458,1.646 true 1.771,1.396 1.083,1.656 true 1.573,0.427 2.188,0.625 0.615,0.198 10 false G198 2.531,1.573 3.146,1.771 0.615,0.198 10 false IG 0.792,1.604 1.406,1.802 0.615,0.198 10 false IND 0.25,0.208 0.563,0.406 0.313,0.198 10 false *a

Disconnect the G198 back sonar or clearance sonar switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G198-5 (IG) - Body ground Ignition switch ON 11 to 14 V
G198-5 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G198-4 (IND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Back Sonar or Clearance Sonar Switch)


OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - CLEARANCE WARNING ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - CLEARANCE WARNING ECU)
a.

Disconnect the G198 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the I8 clearance warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G198-2 (ECU) - I8-19 (CLSW) Always Below 1 Ω
G198-2 (ECU) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR