Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › RELAY › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260456 RELAY G

1KD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 28610 2.INSPECT GLOW PLUG RELAY (GLOW)

a.
A092673

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 82641 3.INSPECT NO. 1 INTEGRATION RELAY

A406470C01
1.438,2 1.75,2.198 0.313,0.198 2.438,1.99 2.75,2.188 0.313,0.198 3.531,1.99 3.844,2.188 0.313,0.198 4.573,1.99 4.885,2.188 0.313,0.198 5.531,2 5.844,2.198 0.313,0.198 0.094,0.094 0.469,0.406 0.375,0.313 10 false *a 1.51,2.021 1.813,2.26 0.302,0.24 10 false 1T 2.51,2.01 2.813,2.25 0.302,0.24 10 false 1U 3.604,2.01 3.906,2.25 0.302,0.24 10 false 1V 4.615,2.01 4.917,2.25 0.302,0.24 10 false 1W 5.604,2.021 5.906,2.26 0.302,0.24 10 false 1S
*a Component without harness connected
(No. 1 Integration Relay)
- -


NOTICE:
·

The EDU relay, IG2 relay, EFI MAIN NO. 1 relay and FUEL PMP relay are built into the No. 1 integration relay.

·

Before performing the relay inspections for the relays of the No. 1 integration relay, inspect the IG2, EFI MAIN NO. 1 and FUEL PMP fuses.



a.

Inspect the FUEL PMP relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - 1V-6 Battery voltage not applied to terminals 1S-1 and 1V-7 10 kΩ or higher
Battery voltage applied to terminals 1S-1 and 1V-7 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



b.

Inspect the IG2 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - 1V-1 Battery voltage not applied to terminals 1V-2 and 1W-4 10 kΩ or higher
Battery voltage applied to terminals 1V-2 and 1W-4 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



c.

Inspect the EFI MAIN NO. 1 relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - 1W-11 Battery voltage not applied to terminals 1W-8 and 1W-4 10 kΩ or higher
Battery voltage applied to terminals 1W-8 and 1W-4 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



d.

Inspect the EDU relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - 1U-2 Battery voltage not applied to terminals 1S-1 and 1U-1 10 kΩ or higher
Battery voltage applied to terminals 1S-1 and 1U-1 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 4.INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

U115459C01
0.771,0.792 1.188,1.073 0.417,0.281 10 false 2K 2.74,0.792 3.146,1.115 0.406,0.323 10 false 2N 5.427,0.792 5.833,1.115 0.406,0.323 10 false 2O 0.104,0.094 0.677,0.5 0.573,0.406 10 false *a
*a Component without harness connected
(Main Body ECU)
- -


NOTICE:
·

The ACC relay are built into the main body ECU (driver side junction block).

·

Before performing the relay inspections for the relay of the main body ECU (driver side junction block), inspect the ACC fuse.



a.

Inspect the ACC relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-1 - 2O-50 Battery voltage not applied to terminals 2N-1 and 2O-23 10 kΩ or higher
Battery voltage applied to terminals 2N-1 and 2O-23 Below 1 Ω


If the result is not as specified, replace the main body ECU.