Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0416  Secondary Air Injection System Switching Valve "B" Circuit Open  P0417  Secondary Air Injection System Switching Valve "B" Circuit Shorted  


DESCRIPTION

The ECM operates the AI VSV relay which causes the No. 2 emission control valve set to operate.

DTC No. DTC Detection Condition Trouble Area
P0416 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in AI VSV relay circuit

·

No. 1 Integration Relay

·

ECM


P0417 Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
·

Open or short in AI VSV relay circuit

·

No. 1 Integration Relay

·

ECM



WIRING DIAGRAM

A413206E01
6.219,1.094 6.833,1.292 0.615,0.198 10 false MREL 6.229,1.76 6.844,1.958 0.615,0.198 10 false AIR1 5.875,1.135 6.333,1.333 0.458,0.198 10 false G56 5.885,1.76 6.344,1.958 0.458,0.198 10 false G56 5.948,0.948 6.26,1.146 0.313,0.198 10 false 36 5.948,1.563 6.26,1.76 0.313,0.198 10 false 24 5.885,3.875 6.344,4.073 0.458,0.198 10 false C35 5.875,4.521 6.333,4.719 0.458,0.198 10 false C35 5.875,5.188 6.333,5.385 0.458,0.198 10 false C35 5.958,3.677 6.271,3.875 0.313,0.198 10 false 16 5.979,4.323 6.292,4.521 0.313,0.198 10 false 13 5.969,4.979 6.281,5.177 0.313,0.198 10 false 14 6.24,3.854 6.854,4.052 0.615,0.198 10 false AIP2 6.229,4.51 6.844,4.708 0.615,0.198 10 false VCAP 6.219,5.188 6.833,5.385 0.615,0.198 10 false EAIP 6.396,5.698 6.854,5.896 0.458,0.198 10 false ECM 4.49,3.656 4.948,3.854 0.458,0.198 10 false +BL 4.708,3.875 5.323,4.073 0.615,0.198 10 false AIP2 4.74,4.51 5.198,4.708 0.458,0.198 10 false VC2 4.781,5.188 5.24,5.385 0.458,0.198 10 false E22 4.198,5.031 4.813,5.229 0.615,0.198 10 false GNDL 4.156,2.74 5.073,2.938 0.917,0.198 10 false AI VSV 2.823,2.563 3.74,2.76 0.917,0.198 10 false AI VSV 4.969,2.417 5.281,2.615 0.313,0.198 10 false 1U 5.021,2.219 5.177,2.417 0.156,0.198 10 false 2 4.958,1.771 5.271,1.969 0.313,0.198 10 false 1U 5.01,1.563 5.167,1.76 0.156,0.198 10 false 1 4.938,1.135 5.25,1.333 0.313,0.198 10 false 1W 5,0.927 5.156,1.125 0.156,0.198 10 false 8 3.573,0.75 3.885,0.948 0.313,0.198 10 false 1U 3.865,0.76 4.021,0.958 0.156,0.198 10 false 3 2.448,0.75 2.76,0.948 0.313,0.198 10 false 1W 2.771,0.76 3.083,0.958 0.313,0.198 10 false 10 2.792,0.333 4.167,0.531 1.375,0.198 10 false EFI NO. 2 1.594,2.104 3.74,2.302 2.146,0.198 10 false EFI MAIN NO. 1 0.896,1.927 1.531,2.302 0.635,0.375 10 false EFI MAIN NO. 1 0.635,1.146 0.948,1.344 0.313,0.198 10 false 1W 0.656,0.927 0.813,1.125 0.156,0.198 10 false 4 0.708,2.927 1.021,3.125 0.313,0.198 10 false 1S 0.917,3.771 1.458,3.979 0.542,0.208 10 false 70A FL 1.073,4.927 2.146,5.125 1.073,0.198 10 false Battery 4,5.656 4.458,5.854 0.458,0.198 10 false C45 4,5.823 6.063,6.052 2.063,0.229 10 false No. 2 Emission Control Valve Set 4.667,3.396 4.823,3.594 0.156,0.198 10 false 5 5.146,3.729 5.302,3.927 0.156,0.198 10 false 3 5.146,4.385 5.302,4.583 0.156,0.198 10 false 2 5.146,5.063 5.302,5.26 0.156,0.198 10 false 4 3.969,4.896 4.125,5.094 0.156,0.198 10 false 1 2.833,3.125 6.354,3.323 3.521,0.198 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 1 INTEGRATION RELAY (AI VSV RELAY)
a.

Inspect the No. 1 integration relay (AI VSV relay) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

2.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1U-1 - G56-24 (AIR1) Always Below 1 Ω
1W-10 - 1U-3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1U-1 or G56-24 (AIR1) - Body ground Always 10 kΩ or higher
1W-10 or 1U-3 - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR