Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to terminal IGSW of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A413218E01
1.333,0.448 1.646,0.646 0.313,0.198 10 false ST 2.51,0.198 2.969,0.396 0.458,0.198 10 false AM2 3.188,0.188 3.646,0.385 0.458,0.198 10 false IG2 2.292,0.177 2.448,0.375 0.156,0.198 10 false 7 3.51,0.167 3.667,0.365 0.156,0.198 10 false 6 2.479,0.625 2.792,0.823 0.313,0.198 10 false G2 2.51,0.771 6.49,0.969 3.979,0.198 10 false Ignition Switch Assembly*2 3.875,0.438 5.25,0.635 1.375,0.198 10 false IG2 NO. 2 2.24,1.729 3.813,2.094 1.573,0.365 10 false Certification ECU (Smart Key ECU Assembly)*1 2.24,1.583 2.854,1.781 0.615,0.198 10 false G213 4.24,3.083 4.552,3.281 0.313,0.198 10 false 1V 4.323,2.906 4.479,3.104 0.156,0.198 10 false 2 4.25,2.729 4.563,2.927 0.313,0.198 10 false 1V 4.323,2.521 4.479,2.719 0.156,0.198 10 false 1 3.646,3.385 4.104,3.583 0.458,0.198 10 false IG2 2.854,2.865 3.313,3.063 0.458,0.198 10 false IG2 2.427,3.969 4.573,4.167 2.146,0.198 10 false EFI MAIN NO. 1 3.292,4.5 4.385,4.688 1.094,0.188 10 false EFI MAIN NO. 1 4.229,3.844 4.542,4.042 0.313,0.198 10 false 1W 4.281,3.635 4.594,3.833 0.313,0.198 10 false 10 4.24,4.198 4.552,4.396 0.313,0.198 10 false 1W 4.333,4.021 4.49,4.219 0.156,0.198 10 false 8 1.719,4.188 2.031,4.385 0.313,0.198 10 false 1W 1.75,4.01 1.906,4.208 0.156,0.198 10 false 4 1.729,2.729 2.042,2.927 0.313,0.198 10 false 1S 1.74,2.51 1.896,2.708 0.156,0.198 10 false 1 0.906,2.885 1.823,3.083 0.917,0.198 10 false 70A FL 0.656,1.594 1.729,1.792 1.073,0.198 10 false 250A FL 0.802,4.823 1.875,5.021 1.073,0.198 10 false Battery 3.167,4.823 4.719,5.073 1.552,0.25 10 false No. 1 Integration Relay 4.76,2.885 5.51,3.104 0.75,0.219 10 false IGN NO. 2 5.438,2.729 6.052,2.927 0.615,0.198 10 false G180 5.635,2.531 5.792,2.729 0.156,0.198 10 false 8 5.448,3.448 6.063,3.646 0.615,0.198 10 false G180 5.458,3.823 6.073,4.021 0.615,0.198 10 false G180 5.448,4.188 6.063,4.385 0.615,0.198 10 false G181 5.448,4.583 6.063,4.781 0.615,0.198 10 false G153 5.625,3.24 5.781,3.438 0.156,0.198 10 false 2 5.625,3.635 5.781,3.833 0.156,0.198 10 false 1 5.615,4.031 5.771,4.229 0.156,0.198 10 false 6 5.625,4.396 5.781,4.594 0.156,0.198 10 false 3 4.948,0.271 6.948,0.479 2,0.208 10 false *1: W/ Entry and Start System 4.885,0.698 6.896,0.917 2.01,0.219 10 false *2: W/o Entry and Start System 3.083,1.344 3.698,1.542 0.615,0.198 10 false IG1D 3.49,1.208 3.646,1.406 0.156,0.198 10 false 3 6.167,5.094 6.625,5.292 0.458,0.198 10 false ECM 5.854,2.625 6.469,2.823 0.615,0.198 10 false IGSW 5.875,3.438 6.333,3.635 0.458,0.198 10 false +B2 5.885,3.813 6.198,4.01 0.313,0.198 10 false +B 5.885,4.177 6.5,4.375 0.615,0.198 10 false MREL 5.875,4.563 6.188,4.76 0.313,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Always Below 1 Ω




OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)

2.INSPECT ECM (IGSW VOLTAGE)
U169555E02
2.083,1.885 1.313,2.479 false 2.573,1.813 3.052,2.031 0.479,0.219 10 false G180 0.938,2.521 1.604,2.792 0.667,0.271 10 false 8(IGSW) 0.25,0.104 0.583,0.25 0.333,0.146 10 false *a

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G180-8 (IGSW) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY)

NG

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN NO. 1 relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY)

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-10 - G180-1 (+B) Always Below 1 Ω
1W-10 - G180-2 (+B2) Always Below 1 Ω
1W-10 or G180-1 (+B) - Body ground Always 10 kΩ or higher
1W-10 or G180-2 (+B2) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BATTERY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - Positive battery terminal Always Below 1 Ω
1S-1 or Positive battery terminal - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BATTERY)

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-4 - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)
a.

Disconnect the ECM connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-8 - G181-6 (MREL) Always Below 1 Ω
1W-8 or G181-6 (MREL) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN NO. 1 RELAY) - ECM)

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the NO. 1 integration relay (IG2 relay) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY)

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)
a.

Disconnect the ECM connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-1 - G180-8 (IGSW) Always Below 1 Ω
1V-1 or G180-8 (IGSW) - Body ground Always 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - ECM)

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-1 - Positive battery terminal Always Below 1 Ω
1S-1 or Positive battery terminal - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BATTERY)

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-4 - Body ground Always Below 1 Ω




OK

12.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - BODY GROUND)

12.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Confirm the entry and start system.

Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)

B

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)
13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G213-3 (IG1D) - 1V-2 Always Below 1 Ω
G213-3 (IG1D) or 1V-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)
a.

Disconnect the ignition switch connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-2 - G2-6 (IG2) Always Below 1 Ω
1V-2 or G2-6 (IG2) - Body ground Always 10 kΩ or higher




OK

15.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2 RELAY) - IGNITION SWITCH)

15.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2TR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY